mdbrandy's Content - Page 25 - Classic Z Car Club Skip to content

mdbrandy

Community Member
  • Joined

  • Last visited

Everything posted by mdbrandy

  1. E31 has square exhaust ports, and the N47 has round ones. The square ones are supposedly better. Couldn't tell you why, though. Probably flow.
  2. Back in about 1978, I took a '71 240Z with an automatic, and dropped a 4 speed into it. I'm 99% sure I didn't have to replace the driveshaft. That 1% is just because it's been a LONG time! I remember that I forgot to get the flywheel from the junkyard and had to go back, but was amazed that the pedel brackets and clutch master cylinder hole in the fire wall were already there in the car. I should have changed out the distributor too, so I wouldn't have had to deal with the dual points, but I didn't... So, sorry it isn't a definite, but it's REALLY close to one!
  3. Yes, I think we've established that the generic "OIL" cap was on the early cars. I remember kats translated one of the elephant oil caps for us on another thread, but I can't find it right now.
  4. Thanks for the info 2ManyZ's - I'm looking at a couple of 14" Wheels that MSA sells, so I ought to be in the ballpark. I'm surprized that this question has never come up before, but I couldn't find it in the forum archives!
  5. Neither could I. I figured maybe someone that had recently bought a "14 inch" aftermarket wheel or something could go out and put a tape measure to it...I'd appreciate it :classic: . Essentially, I don't want to increase the steering effort in the car by changing the wheel, so I'd like to get one with a wheel about the same size. So I need to know what size is what... Thanks.
  6. mdbrandy replied to gema's topic in Open Chit Chat
    When I was cruizing cross-country in my 280Z "back in the day", my favorite driving album was REO Speedwagon's double live "You Get What You Play For".
  7. Quick question: When a steering wheel is said to be "14 inch diameter", what does that mean exactly? Is it the absolute measurement from the rim outside to outside, or is it the diameter from the center of the rim on one side to the center of the rim on the other. I'm trying to compare aftermarket wheels to the OEM wheel on my 1978 280Z. The OEM wheel is 15" from outside to outside, or 14" from the center of the rim on one side to the center of the rim on the other. Anybody know? Thanks.
  8. Hmm. The one I had trouble with was in the block closest to the radiator, and was the link closest to the fender. It is marked ACC and IGN. What I don't know is if the circuits in a 1976 car are similar enough to those in my 1978 car to make my experience applicable. Things like the fact that my VR is integral to the alternator, and probably other changes might make my car different enough for it not to act the same. Guess I'm out of ideas. Sorry.
  9. Interesting. Very nice sets of "Z" hubcaps on e-bay seem to go for around $100US plus or minus, depending on how nice they are. The "D" ones go for $400-$500 if they're really nice. I don't know how much Japanese market ones might go for. I'd never even considered that they would be different! (that's another reason I love this site - the first time I owned Z's, from 1978-1989, there was no way to get an international perspective on the history!). Anyway, the shipping would probably be the killer!
  10. Mine showed continuity in some configurations, and infinite resistance in others. I assume you pulled it and tested it off the car, so you changed the configuration by doing that. It might be broken when you bent it back to put it back on. It is my understanding that the fusible links are like very slow fuses - allow a lot of current for longer than a fuse. So, I would assume that shorting a 30 amp fuse across the terminals would be at least as safe as having the link there, since it would blow faster than the link. However, it might also blow too easily; I'm not sure. Getting known good continuity across those terminal should allow the guages to come back up at the acc ignition position even before starting, though. When mine was bad, all the guages were dead. Normally, things like the gas guage would register at acc even with the car engine off.
  11. What year Z? I just lost all my dash guages on my 1978 280Z the other day, and it turned out to be a fusible link. The link looked fine, and if I continuity tested it, it was fine - sometimes. Wiggle it around and it cut on and off. It was the big brown one in the forward fusible link block if you have a late 280. Otherwise, be sure those fusible links really are good. I got new ones from Chloe at MidwestZ, and all has been good since. Good luck.
  12. http://chartermi.net/~benjlv/links.htm That was probably it. "Ultimate Z Car Links"
  13. Rats, and I was going to hop a plane and pry them off your car!:devious:
  14. Is that a set of "D" hubcaps under the table behind your cute kid, kats? :classic:
  15. Here's the one out of my '70.
  16. Just for clarities sake, the link I originally posted went right to the product page, and doesn't have a picture. A couple levels up, there's a picture: http://www.zcarparts.com/store/merchant.mvc?Screen=CTGY&Category_Code=PSDC07A Good luck.
  17. If yours is round with a Z in the middle, it is covering the quarter panel vent. This is what is supposed to be there if you do not have the vented hatch (thin, horizontal vents on either side under the window on the hatch) .
  18. Well, now, I knew that, but I had to ask! Anybody that has some that AREN'T on their cars? :classic: Right....
  19. Can I have them :devious: :classic: ?
  20. The badging that I took off #215 has the white Z. That, of course means nothing as to what it might have originally had, but the badges were metal.
  21. I saw that picture, and I don't believe that it is correct. I believe that the plastic grommet actually clips into the pedal bracket. then, the metal cylinder that covers the end of the cable is clamped into that bracket, and there should be a bolt pulling the clamp together. I had posted the attached picture long ago in another thread, but you can still see the plastic grommet in my pedal bracket. The metal "ball" on the end of the cable then pulls against the plastic grommet attached to the pedal bracket. When you release the hand throttle, the cable slides through the plastic gromment, and the metal ball hangs loose. You can then press on the accelerator and the plastic gromment (attached to the pedal) slides along the cable without pulling it.
  22. I think Chris (26th-Z) has done some research on sources for the Jute...
  23. Seems to me that if you have the factory mounts, you should use them. You'll need appropriate bushings and the steel plates that close off those brackets. I see the metal plates on e-bay now and again. Probably other sources too.
  24. Yup, I was reading in "How to Modify Your Datsun OHC engine..." last night that these gear reduction starters started on the late '78 280's, and apparently went through the 280ZX series. So they ought to be fairly easy to get?

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.