Interior
Discussions about the interior components of your early Zcar.
2,353 topics in this forum
-
- 18 replies
- 5k views
I am preparing my dash to go back in the car and I have forgotten the orientation of the plastic ducts inside the dash (see picture). To make things worse, it appears that I have two (Drivers Side?) ducts. I have consulted the FSM and Fiche, still stuck.:stupid: Could some of you please look at yours (especially if you have a '78) and let me know? Pics, although difficult on an installed dash, would be nice. I am especially confused about the smaller hose that feeds the vent under the steering column. Thanks in advance.
Last reply by sblake01, -
-
- 4 replies
- 2.6k views
I've got a '74 260z and played with the dash for hours, covered all the forums but I can't seem to find how to take it off. Can somebody helllppppp!!!!?
Last reply by abuckingfuffalo, -
- 19 replies
- 6.7k views
Hello, Im the proud new owner of a 72' 240z that i picked up for 900$ Im going to be restoring it and the only thing that worrys me is the sunroof. What are my options as far as replacing it, or filling it? Putting glass in it? I would love to hear what some other owners have done. Thanks, Dane
Last reply by soundmasterg, -
- 2 replies
- 1.2k views
I have a 1971.5 240Z, the car came with a series one console, I have a new series 2 4 speed transmission that I would like to install, will the series one console work with this transmission. Which inner boot do I use with the above setup.Can I use my original early outer boot.
Last reply by mrk3cobra, -
- 0 replies
- 1.1k views
I am wrapping up my interior on my '78 and it is looking like I need some of the screws for the A-Pillars, Dash Finisher, and the two long ones on the front of the Console. I would appreciate being pointed to a source or if you have some, give me a shout.
Last reply by ZCurves, -
- 2 replies
- 1.5k views
I have been searching for the infamous 260z dash emblem for almost a year now and no luck. If anyone is willing to give one up i will recompinsate you with a good deal! the missing emblem is a chip on my shoulder when i look at my dash :oI!
Last reply by Garvid, -
- 15 replies
- 2.4k views
Well the rain has come and its starting to get cold,I turn on my heater and funny thing is nothing is hooked up to the switches.Now my question is where can i find the cables where i can turn on the heater thanks
Last reply by EScanlon, -
- 8 replies
- 2.3k views
Any ideas on how to preserve and protect the chrome vacuum plating on plastic parts and door panels? It seems to be so fragile after 30-40 years.
Last reply by ZCurves, -
- 5 replies
- 7.1k views
I'm looking to put a wooden Nardi steering wheel in my '71 240z. Does anyone know where I can find a Nardi hub adapter for the car? I did a search on the forum and the part number is 4301001003 but apparently its been discounted. I read somewhere I can buy a MOMO hub and then use a MOMO/Nardi conversion adapter. Is this the only route? I plan to install some form of a quick release as well (NRG) to protect my car from thief. Do NRG make quick release in Nardi bolt pattern and pitch? I'm afraid after the hub adapter + the conversion adapter + then the quick release would build up the steering column and make my steering wheel too close to the chest (no to NASCAR style )…
Last reply by bavarian06, -
- 4 replies
- 1.5k views
:mad: Just noticed the new driver-side B/S Weatherstrip from BD that i installed October of last year is torn. Not sure if i should even waste my time contacting BD and order from another place. I looked at other suppliers and have a question, what is "Welting" ? I see it listed installed on some of the weatherstrip's for sale.
Last reply by tlorber, -
- 19 replies
- 5.7k views
I recently purchased some new door panel skins from DatsunParts.com (http://www.datsunparts.com/2334). I had a local interior shop repair the old door panels and install the new skins. They turned out real nice!
Last reply by ZCurves, -
Hello fellow Zophites I’m looking into having reclining seat mechanism covers made for my Z and was wondering how much of a demand there is for them aside from my own. If they turn out nice and if there is enough interest, I’ll see what it’ll cost to have more made. I’ll also look into having covers made for the early non-reclining seats if I get enough interest for those and can get a hold of a used set of covers to work from. I can have them made out of steel or aluminum and they should have the same texture as the original plastic covers. They would be within 2% accurate to the original and they can be painted matt black or possibly have a crinkle finish. Let m…
Last reply by Decoy12,
-
Recently Browsing 0 members
- No registered users viewing this page.