Interior
Discussions about the interior components of your early Zcar.
2,353 topics in this forum
-
- 1 reply
- 1.6k views
Can 280zx or 300ZX seats be placed in a 75 280Z w/o any mods? Just a thought that crossed my mine cuz I 'm thinking of redoing my seats....
Last reply by uberhahn, -
-
- 8 replies
- 1.9k views
I have not done much work with cars, and I am just wondering how in depth of a project is removing the dash to swap a clock? If anyone can tell me what to watch out for and what would be the best way to carry this out it would be a great help. Its a early 74 260. Thanks. -Ben
Last reply by Victor Laury, -
- 7 replies
- 2.9k views
I always had this impression that on the rally clocks there was a timer. Then I talked to someone who had one and they said it just has a calender and no timer. It was for a 74-76 Z. Is this true?
Last reply by v12horse, -
- 9 replies
- 6k views
Anyone had experience getting the original Hitachi radio repaired? I called around in the Portland area with not much success. The shops told me that it will cost $45 just to open and inspect and repairs, if possible, could cost another $60 or $70.
Last reply by go z racer, go, -
- 2 replies
- 1.7k views
Hi. I was wondering if I could get some help. I have an early 260z with a four speed. It does not have the original shift knob and I was wondering if anyone knows what it looks like and if they could post a picture. Thanks a million. -Ben
Last reply by v12horse, -
- 2 replies
- 1.7k views
What is the part called that covers the bottom of the body seal welting in the door opening? It's like a threshold, but I think the threshold is the aluminum piece with the word "Datsun" on it. This piece is right behind it as you look into the car, it's metal with a black plastic covering, has a lip that covers the welting, runs the length of the door opening, and curves down into the interior of the car. It then screws into the inside of the car, near the floor next to the seat. Is this the scuff plate? I am in need of a left and right side, and I want to be sure of the name before I place an order.
Last reply by Si|v3r72, -
- 4 replies
- 1.7k views
Ok.... The blower motor in my z is shot... I think some woodland critters called it a home for some time now.... Well I need to replace their home with a new one and I really don't know how in the heck to get the thing out... Do I need to take the dash off to best get to it or can it be done as is??
Last reply by bigd652, -
- 3 replies
- 1.7k views
Can a 240z Horizontal pleated kit fit the 280z seats? I bought this 240z kit very cheap & wanted to put it in my 75 280z. I know that the pleats are different but wanted to know before I try to put them on. If not, I will sell it for $75.00 Dark Brown..BRAND NEW...
Last reply by lance75_280z, -
- 8 replies
- 2.7k views
Just bought and started restoration my 240Z.I think there are some switches and indicators are missing on the console and the dash. Could anyone help me to complete the set up?. I have no, Choke indicator and original choke set up Rear window heater switch and indicator
Last reply by Mr Camouflage, -
- 23 replies
- 3.3k views
Hey guys, I've seen decals to apply to your guage faces that are white, but I've been looking all over the internet and can't find them anymore. Does anyone know what I'm talking about and where I can find them? Any help is appreciated.
Last reply by Alan Pugh, -
- 1 reply
- 1.5k views
The 71 Z I recently bought I found sitting at my neighbors ranch, he informed me that he thought mice had been living in it. I found evidence of this, they leave clues laying around, so I set out on finding the nest they used. It turns out they turned the heater into an apartment complex. I removed the heating system completely and obviously cleaned it very well. Though the mice had ripped apart the foam padding for thier nest that is on each side of the little door in the heater that you open and close to allow air to blow through. Is there a place to buy replacement foam pads to stick in there, or would I be better off getting a similar thickness foam and cutting o…
Last reply by beandip, -
seat removal
by bart- 2 replies
- 1.6k views
OK before I go and start removing nuts and bolts I wanted to ask what to I undo to remove the seats. I have an 81 VW and there is one nut to remove and the seats slide off the tracks, is there anything like this or do I remove the four nuts that I think I need to remove to get the seats out. I realize this is sort of a stupid question but I want to just check. Bart
Last reply by EScanlon,
-
Recently Browsing 0 members
- No registered users viewing this page.
