Interior
Discussions about the interior components of your early Zcar.
2,353 topics in this forum
-
- 8 replies
- 2.6k views
The dash lights on my car ('71) are really dim. The bulbs are new. The brightness adjuster goes from "off" to "barely on." Could this be the fault of a bad adjustment switch? Are they hard to replace?
Last reply by EScanlon, -
-
- 2 replies
- 2.1k views
These are the Corbeau VX 2000. The base is 20 inches wide and 23 inches deep. It is 22.5 inches wide at the shoulder. 35.5 inches tall. It's gonna be a few days before I can measure my car, so I was wondering if someone already had the cockpit dimensions comitted to memory. http://www.corbeau.com/brochure/VX2000.shtml
Last reply by WillieBoy240z, -
- 4 replies
- 1.9k views
Does anyone know where I can get some interior rear plastic panels for my 1975 2 seater 260z from I need the two rear quater panels and the very back panel. Do they remake them anywhere in the world,
Last reply by EScanlon, -
Has any one had good results form filling dash cracks?
Last reply by madsoul, -
- 5 replies
- 2.3k views
After spending a couple of hours everyday this week I finally got the dash loose in my 71 parts car ( it was a major PITA). It is crack free and I want to put in my 73 car that has alot of cracks in the dash. Does anyone know if the wiring is the same or even close? I was thinking of swaping some of the gauges if I have to to get it to work. Has anyone tried this and was it successful? I'm starting to understand why you see so many advertisments for dashcaps. Thanks, Mark
Last reply by WillieBoy240z, -
- 2 replies
- 1.7k views
Are there any aftermarket shifters that will fit the 280Z? BTW, is there a designation for the 3-speed auto trans? Like Ford's C-3, C-5, or chevy turbo 350?
Last reply by TomoHawk, -
- 2 replies
- 1.8k views
Here is my issue, My driver car seat is in terrible shape, the left side is lower that the right and it is cambered to the left. I am afraid my spine will become mis-aligned! and i hate the feel of my left arse-cheek being lower than my right while driving:). I have a chance to get a used car seat from a 76 z car at the junk yard. the passanger seat in this car looks almost new!!! will it fit into the drivers position? or must i use a driver seat? the one in the junked car is in fair condition. Thankyou zcarsrock!
Last reply by kmack, -
- 3 replies
- 2.2k views
Anybody know if 300ZX seats will fit in a 240Z? I'm sure I'll have to do some seat-rail modifications, but I wondering about the dimensions. Will They Fit?
Last reply by ZmeFly, -
- 3 replies
- 2.2k views
Her's something I saw at kitcarz.com. At $295, it's cheaper than a dash rebuild. I wonder if anybody here has had any experience with it or has at least seen one up close. The small picture here does it little justice. http://www.kitcarz.com/dashboards.htm Any thoughts?
Last reply by Ron Carter, -
71 needs new dash 1 2
by derk- 14 replies
- 2.6k views
Hi guys. Took the plunge and am owner of first Z, a 71 I am bringing back from the dead. Not a big fan of dash covers but are there any replacement dashes left on the market?
Last reply by WillieBoy240z, -
- 0 replies
- 1.7k views
I just bought another 260 and the seats had pull over seat covers. Underneath were the vinyl type but with a suede type seat inset and also in the back support area. The rest of the seat fabric looks like my stock vinyl. My question is; was this aftermarket or original? This car is an automatic where my first one is a 4 speed. This one is getting sacrificed to the god of rust repair.
Last reply by bduprees, -
- 2 replies
- 2.2k views
My drivers side seat has a tear on the seat. Whats the best way of replacing this? Can I just find another seat and remove the vinyl from it and install it onto mine, is it an easy thing to do? OR would it be better to find another drivers side seat and replace just the base of the seat. Thanks.
Last reply by 24OZ,
-
Recently Browsing 0 members
- No registered users viewing this page.