Parts Swapping
Thinking about swapping parts from another model Zcar?
601 topics in this forum
-
- 1 follower
- 7 replies
- 1.7k views
EDIT: I think I'm going to buy the big C style. I just tried a pry bar I have on another head and it worked pretty good. I might make a wooden pry bar for under the cam, a hammer handle works pretty darn good already. I'm wanting to get my cam lobes centered with my rocker's pad. I'm going to try this myself. I know that will be looked down on but I have more time than money. The head is off the car and I can't decide which spring compressor I need. If I get the one that hooks to the cam whats to stop the valves from pushing down? I have a 1" x 1" or there about block of wood for breaking the collets loose. But when I get ready to set each rocker up I'…
Last reply by siteunseen, -
-
- 1 follower
- 2 replies
- 1.9k views
Anyone ever buy a harness and notnuse it or even part out a swapped car? figured id check before buying a new one. Sent from my SM-G900P using Tapatalk
Last reply by 92R32GTST, -
- 1 follower
- 8 replies
- 1.6k views
Anyone has a complete ignition, doors and trunk locks and keys set. Mine are worn and would like to buy a restored set to use with the same key for all locks.
Last reply by jalexquijano, -
- 1 follower
- 3 replies
- 1.6k views
After 39 years of dutiful service my A/C compressor has frozen. I actually had the hood up watching the motor idle as it happened. I saw a brief post on a forum that alluded to a 300ZX compressor fitting the 280Z but the post was left unfinished. Is there a swap from another year model I can use?
Last reply by zcarnut, -
- 1 follower
- 5 replies
- 1.6k views
Hi! Steve from Brownstown here. I have a 77 280Z auto that I'm converting to a 5speed from a 82ZX. I wonder if the clutch/brake pedals or assembly is compatable with the 77Z. Also have extra parts from the 82ZX available. All the glass is good. The body is rusted, however it had almost new fenders on it. Still can read the made in Taiwan stickers on them. Thanks if you tell me about the compatability with the clutch/brake assembly.
Last reply by Patcon, -
- 1 follower
- 14 replies
- 7.4k views
Hi - I've replaced my stock 240Z distributor with an E10-80 from a 1980 280ZX. I've replaced the advance plate mechanism, magnet ring and now also need to replace the vacuum advance which bolts onto the outside of the dizzy. Does anyone know the correct part number for a *single-line* vacuum advance which will fit into this distributor form/fit/function? Note, the original 280ZX vacuum controller had 2 vacuum lines -- I think one was advance and the other for anti-backfire retardation -- but I only need a simple 1-line controller which has the correct mount hole location and arm length. Thanks in advance, Sean Gillen Arlington, Tx
Last reply by jalexquijano, -
- 1 follower
- 4 replies
- 1.4k views
I'm just about finished restoring my 71 (2-1971) 240, the center section of my rear bumper is bad dented, does anyone have a center section, or a whole rear bumper for sale or trade? Also need rubbers for rear bumper and windshield wiper arms. Thanks, ericjump@aol.com
Last reply by CDL1542, -
- 3 replies
- 1.4k views
Has anyone measured the extended and compressed lengths of both the 240 and 280 half-shafts (left and right sides)?
Last reply by Zed Head, -
- 1 follower
- 2 replies
- 1.3k views
hey fellas. Anybody know of a 280z getting parted out in Spring TX? Looking for a AFM and other miscellaneous parts.
Last reply by ZCurves, -
- 2 replies
- 1.4k views
Was wondering if anyone happened to have a portion of the passenger side inner fender from a 240z that they'd be willing to sell, looking for the inner fender from the firewall to the strut tower about.
Last reply by cbuczesk, -
- 4 replies
- 2.6k views
S1 240 Parts Sale or Trade. Make me an offer. You pay shipping. Taking up room 70-72 SU Carb Air Cleaner - no bolts 73 240Z Bumper Guards 72 240Z Rear Bumper with Guards 34 inch spacing ?? 240Z Rear Bumper with Guards 30 inch spacing 240Z Front and Rear Bumper Overriders MSA 240Z Front Bumper MSA Flush Mount Mirror Kit 200SX 80-83 Hubcaps (don't know why i have these)
Last reply by auzziez, -
- 13 replies
- 3.9k views
I picked up a cheap L16 original atsugi water pump and have started researching to see if it will fit my L28. I know about the pulley offset problem and was wondering if anyone has swapped water pump pulleys from another datsun to correct the offset problem. The size of the impellers looks comparable to the L28 pump despite the fact that its for a smaller engine. Since the source of LD28 water pumps has long since dried up, I ran across a page where someone compared the impeller size on the Z20-22-24 and it looked like the LD28 pump with the larger impellers and the post said it bolted on the L4 with no modification. But there again the problem of L4 and L6 pull…
Last reply by siteunseen,
-
Recently Browsing 0 members
- No registered users viewing this page.