All Activity

What are Euro-Top pistons? What did the chambers measure out at? Just curious about compression ratio. You should add a driving video. Good luck.

Pretty car. I like the clean engine bay

It's a pencil tray

1978 280z I want to replace my fusible link holder with a new blade fuse box. When I search here, I get thousands of post to review. Many fuse boxes are listed on Amazon and other sites. Any thoughts on the better ones to use? .

What is that, an ashtray?

They are not mismatched, they are identical parts, just one (right) is a complete zero hour rebuild. The front and rear Tokico's are very low mileage, I installed them shortly after I bought the car. The insulators are new. They were removed because the rebuilt one was leaking but I did not plan on having car off the road for months during peak driving season so I installed BC coilovers to keep the car on the road. I am less than satisfied with coilovers compared to gas pressurized Bilsteins, but I'll live. I put them up for sale on the off chance that someone might have project car that could use them, but eventually if they don't sell and i come across front and rear struts for the swap back (old struts were cut to accommodate coilovers), I will go back to Bilstein's and sell BC hardware. Below is car they are installed in (1972 240Z, Weber DCOE 40 six pack, recaro seats, roll bar, strut bars front and rear plus other mods. HTH, Willie

Does anyone have fastener specifications (size and grade)? Thanks, Keith

Nice! What parts did you have done?

Mismatched and high miles. Yikes. Why were they removed? What's on the car now?

I just went over to the shop that applied the paint protection film and Clearplex windshield film to my Zed. It looks great. He will keep it overnight so that the film can fully cure and them give it a once over before I pick it up tomorrow afternoon. Here's a preview. I'm already for some road trips this summer. 😎

I currently have a top shelf suspension for sale on ebay. Give it a look: eBayBilstein gas pressurized strut cartridges (front and rear...Direct fit with gland nuts. New strut insulators. You will not find a set of these period Bilsteins anywhere. The car will corner like it's on rails and there will be no play in suspension. They ar...Willie

Pictures are available

1980 Ground Up, DATSUN 280ZX. Body completely disassembled, stripped of all paint, undercoated with POR15 & painted. No damage or rust. ENGINE; L28 with Euro-Top pistons, P79 head, ported & polished and CC`d. 60mm throttle body, custom intake manifold both Jet Coated, custom fuel rail with 14mm o-ring injectors. Wolf 3D engine management system with 6 Denso Coils, sequentially triggered. Center Force light weight flywheel & clutch. SUSPENSION; Polyurethene Bushing, KYB shocks, Suspension Technique sway bars, R200 differential 3.54.1, Panasport Wheels F15x6, R15x7. 8,302 miles since rebuild. Not driven in the rain. All receipts available. Much more $18,000.00

Guess I'll put it here as this is, at least to this old buzzard, the path of least resistance After almost 190,000 miles and a bit of bearing noise I decided to give the 5 speed in my 78 280 the business and @ the same time address all of the related issues. At the risk of glazing the eyes of my audience I promise to be brief. I had the rear engine plate powder coated - yes, I know it was clear zinc plated from the factory but I wanted to see what my very excellent powder coater could do and the results are very satisfactory - removed 4 pounds from the stock 24 pound flywheel, had the now lightened flywheel balanced along with a new pressure plate, replaced the rear engine seal, clutch assy - used the Exedy set for probably the 100th + time in my career - flywheel and pressure plate fasteners, ALL of the trans bearings, 2nd and 3rd gear syncros, seals and gasket and had all of the related fasteners, etc. zinc replated. This past Sat I drove the 350 mile round trip to Import Carlisle - touched 100 MPH for a couple of seconds - without a hint of concern. I got those trans parts I could from Nissan - yes, I know there are some cheaper alternatives but I like the guys at my fav dealer. Those bearings that are NLA from Nissan I got from a company in Japan, Amayma. They, Amayma, provide excellent service and excellent prices for parts in the original Nissan packaging. Way back in 1971 the dealer I was working for sent me to Datsun trans school. The school held @ Datsun eastern headquarters in Secaucus, NJ. The dealer provided me with a NEW, just off the boat, 510 2 door for transportation. Yes, a new 510 2 door was capable of an indicated 100+. We were provided lunch at what was, I'm confident, a mob owned restaurant. Our instructor told us we could order ANYTHING on the menu but if we wanted lobster we had to give one day notice. Those were the days.

I would guess that either are fine shocks. The biggest difference is the Koni's are adjustable.

Early starter fuse link on left and early alt fuse link on right. I'll put it on my site when I have some spare time - retirement is SO BUSY!! Story about recent 5 speed rebuild and my time @ Datsun trans school so very long ago to be posted momentarily

I'm still waiting on a response as to why it's my fault that the door latch holes were in the wrong place and the door panel won't go over the ledge. I will say the door weatherstrips fit great and the rubber fuel filler neck fit perfectly so you do sell good parts. Just not these doors. Keep in mind I reverse engineer items and create foundry patterns based off of that gathered data. That is my business. I also reverse engineer fabricated items and make them into castable items. So when I say these doors have a problem and when I say your QC is nonexistent and when I say they aren't using welding fixtures to locate critical weld in place nuts and when I say they aren't using drilling fixtures for holes in critical areas you can take that to the bank. Because people pay me to do this. I just happen to have a Z car and I'm also a manufacturer of parts for these cars. Max you keep stating how many items you have sold as a baseline to the quality of the parts. I specifically said to you in our first conversation on the phone, how many of the 30 door sets that you sold are still sitting on someones shelf. Have you sent emails out to everyone who have purchased doors warning them of potential problems or are you just kicking the can down the road hoping for the best.

Same set up as used on the 510 wagon!

So you probably have over 100 potentially disappointed customers out there. Good luck with that. The fact that they were purchased does not mean that they are of good quality. It means that people expected good quality, like these two disappointed individuals did. Besides the possible disagreement on quality, the problem here seems to be the lack of communication. Anyway, these things are not uncommon. At least you have a dialog going now. Good luck.

It's been documented, with measurements.

Why is the assumption the parts are bad? We are the largest manufacturer of S30 parts and have great reviews, we sell hundreds of parts per month. We would not be able to do this if the parts were poor quality. We have sold over 100+ of the lower valance kits and are on our second batch now, this is the first return of this item we’ve had. We have less than 1 percent returns year after year, the allegations that the parts are “poor quality” based on the feedback of a few individuals that were offered help/other options does not seem like a fair assessment.

That answers the Summit question. But it looks like you know that the parts are bad but are trying to hold on to the money that you received for the first set of bad parts. It's like the old ads for lifetime replacements. Replace bad with bad. Long-term the remaining question is "are you addressing the poor part quality?" Will anybody buying parts in the future get the same bad parts or will they get new "fixed" parts? You haven't said that the parts are actually good, you've only said that the individuals paid for them and that you'll replace bad with more bad.

The customer ordered it from Summit, they declined the return because he used one of the pieces and only wanted to return the other 2 pieces. We offered to send him a new kit for free, I would call that “eating it” would you not? We didn’t get his order but were still offering a solution.

Outsider view - it looks like Resurrected Classics got screwed over by thier supplier and has decided to pass the damage on to their customers instead of eating it as the cost of doing business. But, there is a question about Summit. If the parts were purchased through Summit why not return them through Summit? Summit has more leverage than an individual customer. Give Resurrected Classics the details, but return through Summit. If Summit stops selling the parts, then the responsibility goes back to where it belongs. Companies that get their products from off-shore suppliers really hate to get returns. Probably because they have to eat the cost. Communicating with companies in Asia is very difficult. I got a bad mirror from MSA many years ago, obviously bad, the image looked like a funhouse mirror, and it took some serious persuading to get them to send me a good one. Probably because the bad one could not be fixed, it was garbage. MSA had to but two mirrors to get paid for one. Commenting more from the perspective of how global business works. Many ways to get screwed. I wonder if Alibaba is involved. https://www.alibaba.com/