SteveJ

Contact https://vintagezparts.com/. He has dismantled a lot of Z31s. He might be interested, and he is in NC.

I have the driver side 73 out. I'll try to remember to take a photo.

For the turn signal switch, this may help. https://fiddlingwithzcars.wordpress.com/2012/12/04/turn-signal-repair/

Welcome to the forum. I see you're in my neck of the woods. I'd appreciate it if I could come by some time.

Thanks for posting the links.

On Figure BE-2, it is identified as "Switch Element". Yellow/red tends to be power for gauges. The only yellow wires I could find were from the fuel gauge to the fuel sending unit and from the intermittent wiper relay to the wiper motor. Unfortunately while all of my answers are accurate, they don't do much to provide you with the information you're really looking for.

Is it a three wire connector? Confirm wire colors. It looks like white/red, white and black. Wire colors and connectors are everything when you are asking these kinds of questions. Edit: In blowing up the picture, I see that I confused a shadow for a black wire.

I could look at another spare gauge, but that won't be until next weekend at the earliest.

It's probably the same part number as for the 260Z. When I had one of those apart, I did not notice a mechanical adjustment, but I wasn't looking closely at it. It's not too difficult to remove, open the case, and inspect if you want to, provided you don't have factory AC in the car.

I got plenty of photos of the two of you on the track. I felt bad for Andy when I saw the right side had been severely pancaked. I'll eventually get links up to the photos.

You'll need a pin removal (extractor) tool. However, I don't know which one you need for the round connectors. Edit: This one gives you options: https://www.amazon.com/Lisle-56500-Terminal-Tool/dp/B0009OR906 2d Edit: Just search for pin removal tool at Amazon under automotive. There are a lot of choices like this (https://www.amazon.com/ILamourCar【11PCS】Auto-Terminal-Electrical-Connector-Extractor/dp/B07B2P7D7L) and this (https://www.amazon.com/dp/B075KLM6R9/ref=sxbs_sxwds-stvpv2_1?pf_rd_m=ATVPDKIKX0DER&pf_rd_p=2708083022714283574)

Quick reference: http://www.carpartsmanual.com/datsun/Z-1969-1978/body-260z-280z/2-seater/door-lock-regulator-handle If you are missing part of the lock, the door lock part numbers for your car are 80502-N4420 Right 80503-N4420 Left

That is not a separate part. It is a component of the door lock. It's the same part number for the 77 and 78, but the 2+2 uses a different part.

Is there any chance the rubber brake lines at the wheels are ballooning?

So did you check the orientation of the brake calipers?

Yes, it is unusual. The typical suspects are a battery going bad and loads added to the wrong side (battery side) of the ammeter.

For me, I just would repair the dash harness, but I am hard-headed that way.

Check the calipers. Make sure the bleed screws are at the top of the caliper. Sometimes people install them on the wrong side, and the bleed screws are down. That traps air to the point that it is difficult to impossible to purge.

That toggle switch is not a Nissan part. From the wire colors I can identify the circuits as parking lights (green/white) and dash lights (blue/red).

That toggle switch looks to be the kludge that the previous owner tried to do when the parking lights wouldn't come on.

I would be tempted to say it's the seat belt buzzer, but that should only have a black wire and a green wire.

And another nice Mitty article: https://jalopnik.com/why-datsun-and-nissan-are-among-the-most-important-name-1825841897

I'm guessing the owner lives in Nashville. https://www.hemmings.com/classifieds/cars-for-sale/datsun/280z/2074218.html

That's a party I should have participated in. I'm going to do a labor swap sometime this spring or summer. A friend will replace my rear bearings while I wire up his Z with relays and LED headlights. Frankly, I think I'm getting the better end of the deal. Of course, I'll probably also be grilling after we are done, so that does even it up some.

Wow. Grease and a hydraulic press. Dang, Capt. You sure do know how to throw a wild party.