Everything posted by mdbrandy
-
Cut Out Wheel Well Rust
From the album: HLS30-00215 240Z Rust
But when you start poking, prodding and cutting, it gets worse... -
Small Hole in wheel well behind rocker
From the album: HLS30-00215 240Z Rust
Only a small hole, right? -
Left Rear Rocker Under Quarter
From the album: HLS30-00215 240Z Rust
After removing the front 2/3 of the rocker, there's what it looked like under the rear quarter panel. Not too bad, right? -
Rust, Rust, and More Rust
Until you start making it "bigger". Abrasive cutting wheels make quick work of removing metal :devious: .
-
Rust, Rust, and More Rust
Here is the wheel well behind that portion of the rocker before work started. Hole doesn't look too bad, right?
-
Rust, Rust, and More Rust
Not much. I had some indications, however. Here is a pic of the rear of the rocker before I started hacking on the quarter panel. Note that the outside of the quarter looks pretty good. The end of the rocker inside it is rusty, but reasonably intact. However, see the next two pics...
-
Fuel tank
There's a purportedly "no rust" gas tank from a '73 on e-bay that no one has bid on yet. gas tank
-
Center dash panel
I glanced in my '78 280Z parts car last night, and the Heater Control Panel is NOTHING like the one in my 240Z.
-
Rust, Rust, and More Rust
Well, a few weeks ago I removed 2/3 of the left Rocker for replacement, and I was vacillating about cutting out the lower rear quarter to get to the back end of the rocker. The quarter panel had been replaced 12 years ago and still seemed to be in good shape. I think it was Escanlon that suggested I might consider what things looked like under the quarter, and tonight I did. Poke, prod, cut, chisel, and in the end, it looks like this. Yikes! At least I'll be able to replace the entire rocker intact, and then the lower quarter dogleg. Thorough cleaning out, POR-15ing, and maybe I'll never have to do it again. Hopefully. Ugly stuff, that rust...
-
HLS30-00215 240Z Engine Bay
Engine Bay from various angles and disassembly states.
-
Engine Carb Side
From the album: HLS30-00215 240Z Engine Bay
Engine Bay about half stripped down. -
HLS30-00215 240Z Dash
Shots of dash, under dash, and dash disassembly
-
One Heater Vent Cable Connection
From the album: HLS30-00215 240Z Dash
A close up of the connection of one of the heater control cables to the vent. Note the choke cable behind the vent cable. -
Dash Pad Glued Areas
From the album: HLS30-00215 240Z Dash
Areas where the dash pad had flaps of material glued to the back of the dash frame. -
Hazard Switch Area
From the album: HLS30-00215 240Z Dash
Area around the hazard switch. Shows where the decal was, and whatever was in the hole above the hazard switch. -
Dash Pad Removed From Frame
From the album: HLS30-00215 240Z Dash
Here's a pic of the dash pad and frame after disassembly. -
Back of Heater Control Panel
From the album: HLS30-00215 240Z Dash
Back Side of Heater Control Panel after removal from Dash. -
Front of Heater Control Panel
From the album: HLS30-00215 240Z Dash
Front of my Heater Control panel. -
The rest of the back side of the dash.
From the album: HLS30-00215 240Z Dash
The other half of the rear of my dash, removed from car, but before disassembly. -
Part of back side of dash
From the album: HLS30-00215 240Z Dash
Rear of dash after removal from car, but before disassembly. -
Tie Rod Ends - Won't come apart!
There are tools to do that job. The simplest one is a "pickle fork", which is a large, two-pronged fork tool. The fork tines are thin at the front and get progressivly thicker and thus act like little levers that slide on either side of the tie rod end and push it out as you hammer on the end of the fork. Anyone else have a better description? You can get one of these tools at most auto parts stores. There are different sizes for tie rod ends and ball joints. There are also little "press" tools that I have seen that use a sort of clamp and screw arrangement to press the end out of the knuckle, but I've never used one. Good luck.
-
Z Fest / Z's By The Bay
Nope. Same problem even when the address is directly entered in a new window. Do you have the photos somewhere other than the guycali site, and you're linking from this site to them? That sounds like what it is complaining about.
-
Z Fest / Z's By The Bay
I get a "remote linking forbidden for free accounts, please upgrade your account" graphic in place of all your pictures. :disappoin .
-
Center Dash Restoration
I'd say NOTHING is necessarily obvious - even with the picture, I might have not thought about it and routed it wrong. Especially since it will be a year or more before I put it back together! Tips like this can save hard-to-find parts! Thanks!
-
Center dash panel
The parts fiches list 5 different panels up to '73, with a break at 7/72. Then, after 10/73, it's a whole nother fiche, and the part number is different and the drawing looks pretty different. I don't think a '76 finisher will work in a '72, although I don't really know. I'd get a picture and compare - that ought to tell you.