Jump to content

Dude

Members
  • Posts

    38
  • Joined

  • Last visited

Everything posted by Dude

  1. That’s great info I am going to check out there site right away thank you so much zspert!??
  2. Well I trust someone that has used them and gives it a good word so I will save up my pennies to get my hands on them thanks for the info ???
  3. Patcon I had a question I looked up bad dog sway bar plates which I want to get now but the frame rails cost a little over $200 for the fight I think a little over $100 for the back but I saw them on zcardepot $89 my question to you is does “bad dog” make better frame rails replacements? Or are they the same thing?
  4. Ok ?? I’m glad I asked and especially glad for the “fire” ? tip! Hope it wasn’t to crazy. I made a copy of your response so I can do some research because I’m not going to lie I don’t know where all of those spots are but I really appreciate you giving me a map! ???
  5. I was wanting to know if it is worth it to spot weld the seams on my 240z if so is it worth it to do the whole car or just certain portions of the car? I want to use it for track racing and every day driving , also I was about to spray the car with rubber undercoating and I want to spot weld before if it’s better to do so. I know there are some pros on this forum they can give me the best advice
  6. Dude

    Platting

    Ok everybody I now feel more confident on getting this done with all the advice I was given, and it’s great advice and makes a lot of sense to bag and tag and to use thin wire to keep it all together! Thanks ?
  7. Dude

    Platting

    This is going to be more of a hassle trying to figure out what is the most important parts to platte first
  8. Dude

    Platting

    This is going to be tricky to figure out what to platt and not?
  9. Dude

    Platting

    Well I have my work cut out for me thanks ??
  10. Dude

    Platting

    WOW can’t say I want to go as far as the eternals but I would like to some main pieces done. Is there a basic list of the parts I could get platted?
  11. Dude

    Platting

    I am tearing down my 70 to 240z and before I put it together I want to get some parts plated just wanted to know if anyone happens to have a list of every part that I can get plated on my car before I put it all together?
  12. I have learned that replacing everything on my 240z takes special fabrication, knowing someone that can help, and luck! ? so thank you once again ??
  13. Right on I’m tackling it tomorrow and probably just gonna cut the off cause the very brittle
  14. Ok now I feel more confident on getting it done! And honestly I might as well get all new rubber since I got it all apart anyways and thanks for the site cause that’s always a pain trying to find the best place to get parts! ??
  15. Patcon I’m trying to remove the wiper motor
  16. Hoping someone can tell me how to remove this rubber grommet that holds the windshield wiper hardness cable does it pop off in half or do I have to cut off and buy a new one?
  17. Siteunseen ok great thank you sooooooo much for the info on watching out for some of them being a little to long. So on that note I will start saving up to buy this ? and try to convince my wife to let me buy it sooner then later ?
  18. Also I found a complete 240z set for $269 at www.zcardepot.com do you guys think that is worth the money??
  19. Sorry Jag.series1 & chsheen1 yes you’re both right hard to find and I have been reluctant to by the sets they have cause of how much it is but if my OCD just might make me bite the bullet and buy them— and I will check out that sit “boltdepot.com” and see what I can find thanks guys! Also I found a complete 240z set for $269 at www.zcardepot.com do you guys think that is worth the money??
  20. Jag.series1 & chsheen1 yes you’re both right hard to find and I have been reluctant to by the sets they have cause of how much it is but if my OCD just might make me bite the bullet and buy them— and I will check out that sit “boltdepot.com” and see what I can find thanks guys!
  21. I’ve had to take part in my fenders on my car and is doing so I found out that a lot of my bolts washers lockwashers are either pretty worn and I had to pry out with the vice grip and destroyed them——I’m wondering if it’s best that I just go to my local hardware shop and buy the ones I need OR I have seen kits sold from different websites. Can anyone tell me what they think and if buying the kit which website I should choose to purchase them from? Thanks in advance
  22. Dude

    Measurements

    Thanks Zed Head I actually needed the measurements so I could get my weld in camber plates from AZC installed correctly and as for the type of Strut bar yes I will be looking for a tent style. Do you happen to know of a good brand I could use since the bolts will be missing after that section gets cut out?
  23. Dude

    Measurements

    I need to weld it in my camper plates on the front and back strut towers of my car I wanted to know if anybody knew the measurements from the center hole of the strut towers from right to left of the engine bay and the rear strut towers ?
  24. Wow that looks awesome! And yea the mounts ont the front of the 240 are a little different but other then that it’s spot on??? let me know if you’re able to get the dash on without any issues k ?
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.