Zed Head

Sounds like somebody has messed with your vacuum lines and was unable to resist the urge to connect a vacuum line to the "Sorry:" piece. Not uncommon. The dashpot does not use vacuum, it's open to atmosphere. Make your vacuum lines look like the diagram. Get a three-way connector.

They're for "NVH" reduction, I believe. I think that stands for Noise, Vibration, Harmonics (or Harshness), They stop the transmission from wobbling around on the back of the block. Not going to help your oil leak but might make for a quieter ride.

The guys were right, sounds like the BCDD. But the symptoms are odd. Usually they just stay at high idle, they don't correct on their own. Seems like yours might just be gummed up. It's the weird thing hanging under the throttle body. Later ZX's had them on the manifold.

Here it is. No post numbers in the thread, it's about 80% down the page. cygnusx1's post. https://forums.hybridz.org/topic/95316-braaps-l6-efi-induction-advice-and-tips/#comments @cygnusx1

So is there only one circuit board in the microprocessor ECU? Not a board sandwich like the early ones. Did they shrink the package down, the processor replacing a whole board's worth of components? Would be interesting to see what is connected to the processor. Might also be interesting to compare it to an ECCS ECU. See if it's a step on the progression. Somewhere out there is a list of what some of the components inside the early ECU's do, their functions. Resistors, capacitors, etc. superlen has seen it, I think. @superlen

Is it a 5 speed or automatic? Your description doesn't quite fit. You're blending driving and idling together. Why would you be "at idle" going over 3 mph? Maybe add some details to what's happening? Hanging idle speed is pretty common but has several possible causes. Her's a service manual link.

How about a valve seal? Maybe one bound up then tore. Might be able to see signs from under the valve cover.

EFI, ECU, microprocessor, "computer", "control",,, there are a lot of words being battered about here. The control algorithms coded in to the microprocessor circuitry would tell how much "computer control" was happening. Just because there's a microprocessor in the ECU doesn't mean it was "controlling" the whole system. It could be doing one small part, like handing the O2 sensor data. Response speed would be important for its role in the system. The original question was about the distributor being "computer controlled". Even if there is a microprocessor in one of the EFI ECU's, it wasn't used to control the ignition system. Just trying to keep things clear. Don't want to get in to this guys world - https://www.performancechiptuning.com/nissan/240z/

Purely on the content that you posted. I've known and met people like that. His first words were a denial of something that he could not know, that the mechanic admitted doing burnouts. Then a justification of the thing that he said was not admitted to. I wouldn't trust that guy to work on anything of mine. You can't believe his words.

Classic BS'ing. Art...

Brad's a bullshitter.

Just realized that this thread is in Technical Articles. Probably shouldn't be. @Mike

EFI

ECCS

NA was EFI, turbo ECCS, They're both shown n the 1982 FSM.

It's clear. If I recall correctly, some engines have been built with a separate mechanical distributor for each spark plug. Mechanical COP. Lots of ways to redescribe something. Not sure which will help the discussion. At least we're splitting fuel from spark, which is always important for understanding.

Are we mixing the ECCS system with the EFI sysstem? The ECCS system was used on the turbo engines. Nissan went full ECCS on all engines in 1984, from my understanding, at least for the Z cars. Google found me an old article about it. https://trid.trb.org/view/183990

It does if you want to use it as wasted spark. The system pulls the spark from one plug and pushes it the other. The direction is the same whether it's on the power stroke or the exhaust stroke. It's pretty interesting to look at a set of plugs from a wasted spark engine. Half of them will have the center electrode burned down and the other will have wear on the grounding strap. It's weird.

Ignition module failing is possible. Or you might be losing connection of the blue wire from the coil negative to the EFI, module, and tach. Sudden dying usually means no spark. Losing tach is sometimes a sign of module problems. Check for loose wires first.

For ignition purpose alone, "sequential" and wasted spark are the same, except that the spark jumps backward for three of the plugs with wasted spark. For ignition spark is always sequential. Sequential is a word used to describe injection, when the cylinders only get fuel on their compression stroke. And sequential is really only effective at low RPM, and it's really mainly for emissions purposes. Just wanted to put that out there. Injection and ignition are two separate events. Even when people go to something like Megasquirt, they can do it in two parts, completely independently. Either one can go first. And ignition timing is always done from the crankshaft because timing is based on piston position.

The AFM plug has been known to fall off. Check that. Really need more detail though. Is the engine fully warmed up or cold? Has it ever run right? I know you've posted before but I can't remember the details. Add a a lot more detail. There's almost nothing in this post.

https://www.thezstore.com/page/TZS/PROD/11-2997

It doesn't. You can download a service manual from the site's downloads area. Read the EFEC chapter, it describes the EFI system. The Electrical chapter describes the ignition system.

True. He could modify his also, I'd guess. It's the clamping screw that's the issue. Keeping the ZX distributor is the easiest. It's not connected the to the EFI system. You can keep it and run carbs. I was responding to the question as asked.

https://www.autosportlabs.com/the-new-megajolte-mk2-is-here/ https://trigger-wheels.com/store/contents/en-uk/p72.html https://www.mgexp.com/article/mgb-edis-installation.html