astrohog's Content - Page 9 - Classic Z Car Club Skip to content

astrohog

Supporting Member
  • Joined

  • Last visited

Everything posted by astrohog

  1. The light in the roof of my car works, but the switch part is broken so it is either always on, or always off. Looks like I'll need to get a new one. Can anybody point me to the best source? Thanks! Astro
  2. Thanks, guys! you made it very clear to me now! Anyone know what that part would be called, or if it is available? (the push-fit vent tube, that is). Thanks, Jeff
  3. Thanks, Arne! It appears that the end the p.o. cut off had a small nipple for a vacuum line attached? If I am correct, where did this vac line connect at the other end? Jeff
  4. I have a '71 240 Z. There is a hose that connects on one end to the PCV valve, and on the other end it connects to a tube that comes out of the engine. On my car this tube has been cut short (I think to make room for the York a/c unit). What I want to know is if this tube is just threaded into the engine? Can it be "unscrewed" and replaced with a new part that has not been cut down? If so, what is the part called and is it available and if so, where would I find it? Any light you "gurus" can shed on this matter would be greatly appreciated!!! Thanks in advance, Astrohog
  5. what happened to this thread?? I am dying to hear how it ended! (maybe someone else died trying to get to the end?). Astro
  6. 76 Datsun280Z, I see your located in Wa, but where? There is a great z club in the Seattle area, and I am located in B'ham. Sometime we gotta go on one of the ZCCW drives! Regards, Astrohog
  7. Well, I finally decided to pull the smog pump and A/C from my '71. It went real smooth, and I sure like the amount of room it leaves to access the engine! I guess I should see cooler running temps with the "radiator" part gone. After the A/C was removed, I was able to fit the stock air filter! I took her for a nice drive through the twisties by my place and just had a blast!! She is running better than ever! I am having a blast going through one little bit at a time and each time having success! I am no mechanic, so I am always surprised when my weekend project goes well! I am getting ready to have a stereo head unit installed and then I think I am gonna store her for the winter. Some of the things I hope to accomplish this winter are: pull the tank and boil and seal it. re-foam and upholster the drivers seat and arm pad. all new rubber weatherstripping. I think I will try to strip the factory "sound deadening" and POR-15 the front floorpans. That ought to keep my busy! Regards, Astrohog
  8. Randy, To be honest I have not looked at the A/C that close, but it is mounted on the drivers side and I would have to smash the front air intake to get the stock airbox on! Jeff
  9. Richard, The reason I want to remove it is because it weighs more than a boat anchor, it really takes up alot of space under the hood, and here in WA state I really don't see a need to have a (marginal anyway) A/C in my part-time driver. I tried to put the stock air filter box back on this weekend and it wouldn't fit with the A/C in there. Am I missing something? Anybody else have this issue? Regards, Astrohog
  10. The original owner of my '71 upgraded to the f.m. stereo in '72 (no f.m. avail in '71 !!). I am relatively sure the f.m. was added at the dealer and the switch is located on the inside left of the glove box. I realize this is not very convenient, but it is period correct if that interests you at all. I robbed an electric antenna from a later model Z and I plan to install it in my '71. When I do, I will leave the BIG UGLY switch in the glove box, but utilize the "built in" antenna control that the newer head units have. Regards, Astrohog
  11. For all you "old" R/C guys, there is a new product out there that would be interesting to try in our Z application. It is called "Flite-Metal" and is actually very thin aluminum with an aggresive adhesive already applied. It is so thin that it will "stretch" some and is meant to be burnished onto the surface. It comes in 6" X 25' rolls, so one piece should suffice with no splicing needed. Here is a link to the website: http://www.flitemetal.com/ Hope some of you enterprising sorts will try it out and let us know how it works!! (can you say guinea pig?!!) regards, Astrohog
  12. Here's mine, HLS30-16896 build date 12/70 Astrohog
  13. I am trying to clean up my engine compartment ('71 240Z). When I bought this car, there were all kinds of lines that were plugged with screws (looks like an octopus having spaghetti for dinner!) A buddy of mine came over with his '73 and all his holes were neatly plugged with pipe plugs? or bolts? So I took the lines off today and went on a search for plugs. I am not sure how to explain what holes I am plugging, but I will give it a try. Two of the nipples are the same. One was plugged when I got the car, so I do not know what it was, the other (which is the same size) feeds the "throttle closer delay diaphragm". These two holes are REAL close to 1/8" NPT (pipe thread), but just a hair smaller. I tried 1/8" pipe plugs and they would engage MAYBE one thread and that was all. the other hole I want to plug is to the left og the PCV valve and was plugged when I got the car. It is soooo close to 1/4" NPT, but again is a hair smaller. I work in the fastener industry and have checked metric bolts to match the threads and again, they two smaller ones are sooo close to 10mm X 1.00 (very fine) thread, but are just a hair smaller in diameter. I am thinking they are all metric pipe thread, but cannot find any local vendors that have metric pipe. Am I barking up the wrong tree? Anybody know where I can find some plugs for these holes? Regards, Astrohog
  14. I am looking to remove the A/C in my '71 240Z as I live in WA and just don't need it. What all is involved in this process? DO I need to take it to a certified A/C shop? Will I have to mess with any of the heating system to remove it? Anybody done it? If so, can you give me a brief explanation of steps to take and any pitfalls I may run into? Thanks again for any help, you guys are awesome!! Regards, Astrohog
  15. astrohog replied to mars23z's topic in Carburetor Central
    Actually it is called the "throttle closer delay diaphragm" and it did come on the carburated engines. I took mine off and fixed my problem. When I went to the Nissan dealer, he said they are not available anymore. Regards, Astrohog
  16. Carl, After fiddling with these things, I have decided to go back to the stock air filter box. I just can't find the threaded studs that have a female "coupler" to receive the two cover bolts. Any ideas?? anybody?? Thanks, Astrohog
  17. astrohog replied to mars23z's topic in Carburetor Central
    was having the same problem on my '71. I finally found the culprit. It was the "slow idle return" thing. All I had to do was back the screw out 2 turns and the problem went away. I have noticed, however, that when I shift gears, the idle does want to return to a low idle rather quickly and can make for some rough shifting. I will give it awhile to see if I can get used to it, or I will try to find a new unit and/or fine tune adjust the one I have. Astrohog
  18. You guys ROCK! Thanks for all the help! I will write down all the part #'s you guys supplied and start my search at the local places as well as the e-bay store. Thanks Again! Jeff
  19. Hi All! I just did a search for this and all I came up with was a thread from 2003 that pretty much said "good luck finding a single hatch strut" I have tried a strut from a 280Z that had two struts, and of course, it was not strong enough. My single strut is not strong enough to hold the hatch up and I really would like a new one. I am hoping that between 2003 and now that there is a source for these. Anybody point me in the right direction? Regards, Jeff
  20. dzrt1st - Very cool! I have the oval ones, but those look like what I need! Thanks sooo much! Regards, Jeff
  21. 1 bravo 6 - thanks, but, yes, oil level is fine!! Zeiss 150 - the problem does NOT go away when I tap the pedal. I very well could have some kind of vacuum leak as all the hoses and lines are all original. I will do some closer inspection of vacuum lines. kenz240z - I have inspected the brakes (and replaced the rear shoes!!) Have not got to bleed the lines yet (no brake bleeder and no helper as of yet!:mad: ). You offer very good advice on the flex lines. I will do that next!! Coolant system/radiator was next on my list. As I do not have a garage here at home (hopefully get that built next spring??) I am getting ready to store my Z for the winter and start on her again next spring. Beandip - I will try to get some pics of the Weiand covers for you. I think they are cool looking (and (after-market) period-correct), but have been told the stock airbox is probably better, so as soon as I get the stock box cleaned up, it is going back on! The mech linkage seems fine, but I will have to re-check all of the springs as they are all old and should be replaced. WOW! Thanks for all the suggestions guys, I sure appreciate all of the support!!!! Regards, Jeff
  22. I have not had the domes off, so I know they are not "switched". The piston drops as it should. At least I think it drops as it should! I don't really have any experience with these, but it seems to drop "smartly" as one of my manuals says it should. As this car is all original and appears to never have been messed with really at all, I think it is probably time for the carbs to come off and get overhauled. I might as well learn em now, cause I ain't getting rid of this car any time soon!! If there are any other ideas, I would certainly welcome them, and thanks for all the responses so far!!! Regards, Jeff
  23. I am finally getting my 1971 240Z into reliable running order. I have had her for about three weeks and have replaced the following: tires, exhaust, plugs, wires, distributor cap, points, condenser, alternator belt, battery and terminals. Today, I thought I would take her for a spin as it is beautiful out, so I called my buddy (1973 240Z) and we met up, decided on a route to take and hit it. He had asked me to get up to 80 mph on the freeway so he could check his speedo, so we did...then 85...then 90, when I went to back off the throttle, the rpm's would not drop!! I had to use the brakes to get the r's down and got off the freeway. When we stopped and popped the hood, the mechanical linkage looked fine, no binding, broken springs, etc. The engine would start fine, but idle at 2000-2500 rpm's. when I would give some throttle, it would just stick at the highest rpm that I would feed in with the pedal. I limped her home this way and I am stumped. I pulled the carb covers ( I have the Weiand covers) and started her up. As I fed in throttle to say, 3000 rpm and let off I could feel the piston oscillate a little like it wanted to drop back to idle, but would not, it would stay and the rpm would hold at 3000 and want to continue increasing. I am no carburator expert, so I am not sure where to go from here. Anybody have any advice?? Thanks for any help!!! regards, Jeff
  24. E, My Z has 102,000 orig. miles. I doubt if those were the original tires. They were in very bad shape and that is why I changed them. In fact, two of them had cracked so badly that they actually shed a 4" X 6" "patch" of the tread, leaving steel belts sticking out!! Jeff
  25. Will, I have searched the internet and not been able to even find mention the carb covers I have. I had new tires installed today and the tire guys were laughing as the old tires had tubes in them!! I feel like I stole this car as it was just a driver for all three previous owners, but everything on it is still very stock!! I still welcome any input on this, but I think I will just clean up the stock airbox and get a K & N filter element for it. Seems to be the popular choice, and still maintains the stock beauty of this car! Jeff

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.