Everything posted by kcpope
-
Picked up a 78 280z today. PROS & CONS with some Pics.
It's a good thought, but I don't think that will hinder my smog results. Before the test even begins, the car is left to idle for several minutes to get up to operating temp. So I'm thinking that cold-start injector should be well past OFF at that point. I've had smog techs tell me in the past to drive the car on the freeway beforehand and to get it nice and hot. Apparently that can help achieve better results🤷♂️
-
Picked up a 78 280z today. PROS & CONS with some Pics.
@Zed Head Breaker plate, that's the word I was looking for! That's the piece I remember from my previous dizzy rebuild. It has the little ball bearings in it, yes. I'll add a dizzy inspection and potential rebuild to my list, thanks. And I'll plan on just replacing the plugs with the proper NGKs. No sense in keeping these plugs if they're only "close enough".
-
Picked up a 78 280z today. PROS & CONS with some Pics.
Just documenting my progress as I go along. Today I drained the tank and disconnected any rubber lines to the hardlines both at the tank and under the hood. Going to fill the hardlines with acetone and let them sit for a couple hours. A couple observations: Someone used a non fuel rated hose at the fuel pump so that will need to be fixed 5 injectors appear factory, A46-000001. One aftermarket injector on cylinder 6. Interesting. Pulled all the plugs, and they all look about the same as the one in the pic.
-
Picked up a 78 280z today. PROS & CONS with some Pics.
Great info there, thank you. I'll add cleaning the coolant temp sensors and throttle body to my list. And yes, I can already confirm that I have a crack in my accordion rubber intake tube DOWNSTREAM of the AFM. That will have to be fixed. @SteveJ Good idea, will do. According to the cars history, it's last smog check was in 2008 and it failed and was tagged as a gross polluter, as you said. And in CA, that means you can't register it. No activity after that, which is probably why it was parked. With everything I'm "tuning up", hopefully we address whatever that 2008 failure point was. @Yarb Good tip, I'll do that when the time comes.
-
Picked up a 78 280z today. PROS & CONS with some Pics.
Test procedure: The car runs on a dyno at two steady but loaded conditions while a probe in the tailpipe samples the exhaust. The two sequences are the 50/15 test, 50% load at 15 mph, and the 25/25 test, 25% load at 25 mph. At each mode the probe reads HC (ppm), CO (%), and NOx (ppm). Higher-load mode tends to surface NOx issues, lighter mode surfaces HC/CO issues. Yes, full factory exhaust system is in place, including the cat.
-
Picked up a 78 280z today. PROS & CONS with some Pics.
Ok, would appreciate input on my “tune up” plan for the engine in order to give me the best chance of passing the smog test. As a reminder, this engine runs. But based off the paperwork, it has struggled to pass smog in the past. Last time it passed was 2008, after several attempts. It actually idles ok despite obviously varnished gas. Maybe a little stumble here and there at idle, which could just be the rotten gas. We drove it around and it went through the RPM range just fine. I’m putting these in order of perceived importance. Feel free to re-organize if you disagree. Drain all gas from the tank. Then backflush the fuel line from the engine compartment to the tank to clear any lingering old gas. Remove all injectors and clean them by actuating them them with a power supply while pressuring them with carb cleaner. Check flow rates as Zed Head mentioned? Check for potential vacuum leaks Clean up electrical connections as mentioned earlier re Atlantic Z link Inspect spark plugs. Replace as needed. Check distributor? I’ve rebuilt a 280zx distributor in the past, including those little steel balls that like to vanish. Is that a must here too? Replace fuel filter Replace air filter Change oil with 10-40 VR1 Install correct fusible links Anything I’m missing?
-
Picked up a 78 280z today. PROS & CONS with some Pics.
Thanks everyone for the input👍 Yes, as much as I want to dive into other things on this car, first order of business has to be getting it tuned up enough to pass smog. I'll research how to check injector flows and clean up the electrical connections as mentioned on Atlantic Z. The gas is clearly varnished so I'm going to start by draining that, then maybe dropping the tank and taking a peek inside. Small victory though, I couldn't resist doing something about that bent door corner. Massaged it back into place. Much better.
-
Picked up a 78 280z today. PROS & CONS with some Pics.
Some of you saw my post a couple days ago asking about swapping an auto to a manual on a 78 280z. Welp, I got to see the car in person today, and I decided to roll the dice on it. I've been on the hunt for a couple years and this one checked almost all the boxes. Time will tell if it was the right call... PROS: It runs and drives and stops. The gas is definitely varnished, I could smell it bad. But it still ran, with a little miss here and there. Moved around just fine and went through all the gears. The price was fair. I knew getting an AUTO car would help keep the price down. Car appears to be a lifelong California desert car. Rough on the paint, but great for rust prevention. Doglegs and lower fenders are in great shape. Floorboards and subframe all appear very dry. Battery tray has surface rust, but I've certainly seen worse. Rear hatch area has a few bubbles, but not rotted. The cowl has a pinhole and bubbles located right above that foam block that sits underneath it. As you all know, it's not a matter of IF a Z has rust, but rather how MUCH rust it has. Pretty pleased in the rust department. No side molding! No holes in the sheet metal. I like that. Could it be a 70K mile car!? No way! I'm probably dreaming. I'd be shocked, but maybe. Pedals don't appear worn down. It appears largely stock and un-modified, apart from the wheels. Take it with a grain of salt, but the owner said they bought it from a neighbor whose wife passed away, and it was her car. Who knows, but I would be thrilled if this were the case. Let me know if you have any ideas how I might know. The engine sounds quiet. The usual tick tick of the EFI, but I was pleasantly surprised, even with junk gas. With the cats and the muffler, I can barely hear the exhaust note. Very quiet overall. POSSIBLY 90% original paint. Radiator paint code is present (code 306) which matches the exterior. And I don't see any tell-tale signs of a repaint (overspray onto rubber molding, gas tank, door jamb placard, etc. This makes me happy because I know you can hide a lot of bondo with a respray. I can visibly see all the right "seams" and joints where body panels come together (rear valance, dog legs), telling me they haven't been smoothed over with filler. I say 90% because the drivers rear quarter definitely had some work done at some point. I see evidence of bondo on the bottom lip of the rear quarter. Can't have it all, I suppose. CONS No smog certificate. Seller wasn't willing to hassle with it. Having met the husband/wife sellers, I don't suspect any mal-intent, they just didn't want to hassle with it, and knew it likely wouldn't pass. They've had it on non-op for 5 years, never actually drove it, other than around the block. They had several other people lined up willing to buy it as-is, no questions asked, so I knew it'd be a dealbreaker if I put up a fight. I knew if I didn't buy it, it'd be gone within hours. So I'm rolling the dice here, because I'm in CA and it's a 78, which means I'm going to have to smog it. I know, dumb. It's an automatic. Positive spin, the autos weren't as abused as the manuals:) I'm planning on converting to a 5-speed eventually, so this isn't too big of a deal. Paint is clearly shot, but I'll be leaning into the "patina" look anyways. Drivers door hinge lost its detent stopper, overextended the door, and bent the corner. I think I can work it back into place. Anyways, here's a few pics! I'll keep y'all posted on progress, I'm sure I'll have questions...😄 https://share.icloud.com/photos/057GXCdBmlMhz6-XjN5ifnOGQ
-
1978 280Z Auto to Manual Swap, is the ECM the same?
@Yarb appreciate that input. That gives me some confidence going forward. Don’t have the car yet, so we’ll see if everything else checks out. Rust being my main concern. We’ll see. Seller has owned it for several years, but it just sat in their garage. Left it on non-op and never smogged it. And they don’t seem to want to even attempt to smog it before selling it. It appears all stock with all smog equipment intact, so I’m considering rolling the dice and just buying it, then hope and pray it passes smog. We’ll see what it looks like in person.
-
1978 280Z Auto to Manual Swap, is the ECM the same?
I'm checking out a 78 280z Auto car this weekend. If it checks out, I'd like to manual swap it. I've done the swap on a 72 240Z, so I know the majority of what's needed: clutch master cylinder, clutch hard line, slave cylinder, flywheel and clutch assembly, brake and clutch pedal, etc. My one concern: Is there anything unique about the 78 280z Auto car, like in the ECM or any other electronics, that would cause this swap not to work? Or is the ECM in the auto car the same as the manual cars. Also I'll be dealing with it having to pass smog, unfortunately, but I don't think my manual swap plans will affect smog in any way? Thoughts? Thanks👍
-
buying 240z vs current 280z
Where are you located? I’ve been on the hunt for a decent 280🙂
-
Windshield weatherstrip 280z
I used the one from vintage rubber, and I was happy with it. I think it was $150 or so, which is a good compromise compared to $400🫤 I installed with dash in place using the typical rope method. As far as removal, carefully remove the stainless trim pieces, then use any manor of razor blades, putty knives, flat heads, etc to remove the old brittle rubber, being careful to not chip or crack the windshield.
-
Brake Master cylinder woes
As far as I know, nothing wrong with this approach. I think many folks have had to do this. Kinda a bummer to bend the factory lines, but hey, gotta make it work.
-
Brake Master cylinder woes
Your brake master cylinder should not have any gasket between it and the booster. There is no fluid or air pressure passing between these two parts, hence no gasket or seal. You likely have a leaky master cylinder. The rubber o-rings inside the master cylinder can leak, causing brake fluid to exit the rear of the master cylinder, then it leaks through the (non-sealed) mating surface between the master cylinder and the booster. It then dribbles down the outside of your booster and causes the paint peeling you're seeing. I'd start with a new master cylinder or get your existing one rebuilt. Keep in mind, you have an early 71, so make sure you verify the reservoirs are in the correct orientation on any new master cylinder you get. There was a change in 1973 (i think) that swapped the front and rear reservoirs. For a 71, I believe your front brake reservoir is in FRONT and the rear brake reservoir is in the REAR. in 1973, the designed changed and those were swapped.
-
Lazy Tach with 280ZX Distributor
Still fiddling around with it… Does anyone know what this solid black wire is for? Comes out of the factory wire harness at the coil. It’s the only wire not connected to anything for me. Maybe the ground wire for the old points distributor?
-
Lazy Tach with 280ZX Distributor
Yeah, radio interference, I’ve heard that too. I figured that same interference might be messing with the tach. It’s a long shot, but at this point I figure, why not 😅
-
Lazy Tach with 280ZX Distributor
That’s within spec for your primary. What’s your secondary ohm reading? also, are you running the little stock condensers? One at the coil. One near the alternator. I’m going to try adding mine back in and see if it makes a difference.
-
Lazy Tach with 280ZX Distributor
Yeah, I’ve read mixed things regarding the coils. As Zed mentioned earlier, the 280zx dizzy wants to see around 1 ohm resistance, which is exactly what I have. Did the ZX also have a ballast resistor? In general when people convert a 240z from points to electronic ignition, here’s what I’ve read: if you’re using a 1.5 ohm coil, add a 1.5 ohm resistor as well. if you’re using a 3.0 ohm coil, no resistor needed. This seems to be the case if you’re doing a pertronics ignition, but I’m not sure if the same applies to a 280zx dizzy…
-
Lazy Tach with 280ZX Distributor
Agreed, I’ll do my best to get to the bottom of it. I’d love to not have to swap tachs. We’ll see.
-
Lazy Tach with 280ZX Distributor
Thanks Steve. If I do the swap, I’ll adapt the 260z tach guts into the 240z housing to maintain mounting points and the correct font as zed mentioned. But before I do any of that, I’ll try pulling the existing tach out and see if I can see any obvious problems. As I’m thinking about it more, I’d be suprised if the e12-80 is failing. The engine seems to run too good for that to be the case. PS: the whole reason I needed the tach was to sort out my vacuum advance timing as I mentioned in my other thread. I went ahead and bought a cheap optical rpm gauge on Amazon that I’ll use in the meantime. At least I can get my timing properly setup, then move on to fixing the tach.
-
Lazy Tach with 280ZX Distributor
Good info, thx. I’ll read up on other threads regarding everything needed for the tach swap. Yes, my E12-80 module is factory Nissan. I’m intrigued by the GM HEI swap. Could that be a permanent solution if my tach ends up working with it?
-
Lazy Tach with 280ZX Distributor
Welp, I tried both options I described above. No change. Only thing I haven’t tried is adding the condenser back in the wiring. I’ll give that a shot. Also I didn’t realize that the tach can be pulled without removing the dash. That’s a bit of good news. In the meantime, I’ve found a good deal on a tach from a 260Z. Can anyone confirm if those are voltage driven just like the 280z tachs?
-
Lazy Tach with 280ZX Distributor
Thanks for the info. Interesting. Before I do that, I’m going to try 2 things: 1. Adding a ballast resistor back in with the existing 1.0/12400 ohm coil, and see if that helps the situation 2. I found another coil laying around in my old man’s garage. 1.3 ohms primary, 10600 ohms secondary. I’ll try this coil with and without the ballast resistor as well. Let me know if anyone prefers option 1 or 2 better.
-
Lazy Tach with 280ZX Distributor
***edited my above readings because I wasn't reading my multimeter correctly the first time*** Here's the correct coil readings I'm getting: Primary: 1.0 ohms Secondary: 12400 ohms So this coil appears to be within the specs that Zed Head posted.
-
Lazy Tach with 280ZX Distributor
Good info Zed, thanks. That said, I really want to eliminate all other possible causes before having to pull the dash to get to the tach. Like I said above, I confirmed my wiring at the coil is correct according to the video SteveJ shared. So what's left to test? I decided to check my coil and here's what I got: ***edited because I wasn't reading my multimeter correctly the first time*** Primary: 1.0 ohms Secondary: 12400 ohms Any smoking gun with that info?