Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,085 topics in this forum
-
- 1 reply
- 690 views
my 78 280z recently started to lag when starting, it would take 2-3 turns of key to start. But know it just dosent start. If I use starting fluid it starts right up. Once the car starts it dosent turn off, but the car feels a little shakey in first unless I really push on it. A friend told me it could be a bad injector if so how can I check witch one. has anyone had a similar problem.
Last reply by grantf, -
-
- 10 replies
- 1.6k views
Hee's what I wrote Mike just minutes ago and figured I'd shoot it here as well...... So I'm trying to use the microfiche and it won't let me click on anything and actually come up. I tried the whole "Go into adobe Preferences" thing and the instructions are for adobe reader 4. I have adobe 9 and the "Allow Web browser integration" button is nowhere to be found on 9. What am I doing wrong or is there a new instruction for looking up part numbers on the cd. I only get the first 27 pages and it tells me........ "The document is trying to connect to... file./////E:/ZCD/BASEQ3/PAK/YODA/S30_5c.pdf If you trust the site, choose Allow, If you do not trust the site, choose Block" …
Last reply by Arne, -
- 28 replies
- 4.7k views
Contact me asap if you see this car. It was stolen from the alley between my house and a Vons mini strip mall between two days ago and now. 562-881-5345 1972 240z, RB26DETT w/ RB25 5spd Alpine CDA-9887 deck, PDX-5 amp, 2 Pioneer TS-D902P 6*9s, TS-SW1241D 12" sub Spread the word, engine, rims etc are probably going to get parted out now has chrome mirrors and hatch louvers, missing airdam
Last reply by IdahoKidd, -
- 13 replies
- 3.2k views
hi i have a 71 240z and well my turn signals don't work either on the dash (the green arrows don't show up) and the taillights wont flash. and now to top ti off my headlights and dash lights wont work either turn signals - i checked all the fuses in the center console - the hazards work so i know its not the bulbs - the flasher relay works (bought a new one thinking that was the problem) headlights and in dash lights -bulbs work -fuses work fine -the wipers work i have read other forums on the turn signal problem and they all say check the flasher but that wasn't it and the headlights the same. any information on what to do or check will be greatly appreciated thank you
Last reply by Devil_Z, -
- 13 replies
- 1.5k views
drove to work fine this morning. went out to start it to go to lunch and nothing. volt meter initially read fine. tried to start and it went straight to 0 i have checked battery and fuses. batt at terminal reads 12.5, fuses are all ok, fusible links are as well. now when i engage any light (turn on headlights, brake lights, interior dome light) the voltage halves on the dash voltmeter. removed all light related fuses. still not turning over. any suggestions what it could be? any suggestions as to what to try next? car is a 1976 280z, FI thanks
Last reply by AnthonyG, -
- 17 replies
- 5k views
I would like to mount a four or five channel amp under the driver's or passenger seat in my 73, perhaps a Sony XM4S Slim Line 4/3 or Alpine PDX-5. These are the smallest high quality amps that I can find, but with wires may still be too big. Have any of you mounted the amp under the seat? If so, can you give a model number or any other tips? Thanks. Peter
Last reply by TBone028, -
- 3 replies
- 1.1k views
Im having a noise from tranny like a metal to metal whining noise..when on idle it make noise but if i step on the clutch its gone I just recently change my clutch to Centerforce II..You think my new throwout bearing gone bad, input shaft bearing or clutch mis-adjusted? but other than that they all shifts fine on all gears with no noise..pls help..
Last reply by jbuenviaje, -
- 5 replies
- 1.6k views
My original braided heater hoses have been giving up, they start leaking, i will need a new set, can anyone help me with a part# or even better get me a set and ship it to me. I will not need braided hoses, this is after all the last of the braided there is in the car. TIA Chris
Last reply by ChrisZ, -
- 3 replies
- 1.3k views
Hello, I am in the process of converting from flat tops to round tops on my 74 260Z. I bought round tops from ebay and a rebuild kit from Z Therapy. While installing the rebuild kit from Z Therapy, I conducted a drop test per the DVD. There was one piston that was sticking on the way down. This piston had the same behavior using both domes. I used 400 grit sandpaper to remove some of the aluminum per the DVD. While doing so, I noticed an imperfection in the piston. I've attached photos to help illustrate. At this point I am wonering what my options are. 1) Is there any way to repair this? Should I just keep removing material using the 400 grit sandpaper (does it even n…
Last reply by ChrisZ, -
- 1 reply
- 1.7k views
Removing rear bumper from 280z can't get shocks out!!!!! Undid the 3 14mm on the driverside bottom, undid the 2 18mm on top. Won't come out?! then droped gas tank and unbolted 3 14's on bottom and 1 18 on top need help getting the other 18mm because interior plastic is blocking. How do I remove interior panels? Most of all how do i get thoose shocks out need help fast have work in 5 hours!!!
Last reply by WingZr0, -
ID this trans? 1 2
by mbarjbar- 12 replies
- 5.1k views
Can anyone identify this tranny. Tail is marked 5W71C, body is marked TA71B. I will try to post pictures. Mike
Last reply by zeus88, -
- 2 replies
- 813 views
I was wondering if anyone has a source for the studs that attach the mustache bar to the differential cover? Thanks !!!
Last reply by ironbeast,
-
Recently Browsing 0 members
- No registered users viewing this page.