frank13

Any members in California (So Cal) have any spare Fascia panels laying around for a '71 (5/71). Heater control knobs, fan switch knob, choke knob? I can't seem to find any of these things that came off my Z. I don't know if I lost them all during my last 2-3 moves or what. But I can't find them. At a breaker yard these pieces are always completely thrashed. So I thought i'd ask you guy's. Thanx. If anybody does have any of these pieces feel free to PM me.:devious:

Hey guys, in my experience with my Z and the breaker yards I have not seen the stlye fuse box cover in question on anything earlier than the '73. My first Zed was this year('73), and that is exactly what went over the fuse box. The seat belt lamp was tied into some sort of pressure switch under the seat bottoms, and the seat belt buckles. The choke lamp has a pin switch under the consul at the choke lever. In California I personally have not seen this set up on the '72's.:devious:

Hey smraijck, That whinning noise coild also be a bearing going out. The swap for a latter R200 diff is almost bolt in, with the right mustach bar. From the donnor car. Do a search in the forums for it. The mustach bar is what holds the rear of the diff up into the sub assembly of the rea suspension. If you can wrench there should be no ?'s. By the Z and keep it running.:devious:

No that's information! Thank very much. For at the same time that I was wondering about using these plugs, I also got better info on the heat range and plug types. which I had been wondering about for much, much longer. Damn this place rocks!! . I only need them in there long enough to get her running right on both carbs. I not driving her on the street right now.(no plates). So I see it this way: I need to use anything from spare parts or borrrowed parts to get her ready to run with out blowing the motor. At the same time while I pay off everything that is preessing at the moment I can still work on my Z. When cash allows i'll know exactly what parts to spend one first. Or something to that effect.:devious:

Anybody got any info on swapping plugs(Denso Q20PR-U11) Out of a 1986 300ZX into an L24? I found a new almost brand new set of these Denso's in my stuff and finally through deduction and autozones computer figured they are for the VG30E. The main difference looking at them is the Hex is 5/8 instead of the 13/16 of the 240. Perhaps a tad bit shorter? As for heat range and the like I have not got a clue. But if possible I would like to throw them at my poor 240Z. Not just toss them out. Being that i recently just got her running again after two years. The plugs are all mismacthed from two different engines lying around. Being the hollidays no spare money for my baby's new plugs? Any sound reply's?:devious:

Do you still have the air dam & half dash cover? Do you have pics of these if you do still have them?:devious:

So is those answers a good thing or bad?:devious:

The 1973 did have an electric pump. Even '72 and '71's have the electrical connections for them back at the tank harness. Wrap up in blue tape next to the fuel level sender. That has been stated on this site before. I remember seeing it in a thread before. But since my first Z was a '73 I know it for fact. Not sure if a '70-69 had this connector? I believe that one of the main reasons for the supplemental pump had to do with the nasty vapor lock conditions that the had(have). But for 240's the pump would prime the system regardless of a hot soak condition. Or that's what I learned as my experience with this car started. :devious:

Anybody know if the 280ZX bucket's rails are compatable with the 240's? I Had my grubby little hands on a real nice parts car down at the local breakers. And I actually like the seats for my 240. Only the drivers had one small rip in the vinly. Put I was not sure if they would be a bolt in swap or would needs the rails swapped first. Or made up at the worst. Any one got any Facts on the matter? Thanx Frank.:devious:

Damn love actually exist? My Ex and mother of my two minnie me's also drove a sentra as her first car! Made our first baby in her baby!!!! Haha!!! Anyway she to this day understands my need for Z's. When we were still together and things won't great(or good) I would have to give up the things that I wanted. Another Z, a new bike and on and on. But she always knew just about when I couldn't take not having a Z that was mine. She would run across a Z some where and then behind my back go and find out about them. Later she would say we had to go to this or that store around the Z(s) to see I I would notice them. Then depending on my critic of the car, would go back and try to work out a deal for what ever she had saved up secretly to get me a new Z! Damn. She loved driving in my Z's. Still does. Today out of now I needed to give her a ride to work and after on the way back with her I noticed A '71-72 I haddn't sen on a street I drive down a lot. Hum? Any way one day she will get one Shinny arse pearl whit 240Z('72) all her own! Just because she always loved them with me. Girls are cool, but girls that are into Z's are cooler!:devious:

Hey zztom. If you are getting a lean misfire, you could check you'r fuel line(main feed) from the tank to the hard line in the back. If it's old and chracked it will still run put under load will also suck some air in and kinda give vapor lock or fuel starvation syptoms. you could also check your shop manual for the amount of fuel the pumps should put out while cranking. Then disconnect the out line from the pump and get a cheap measuring cup or the sorts, crank for the amount of time the test calls for and compare. It might also be good to check your advance cannister with a vacum pump/gauge to make sure that your holding vacum and that your advance cannister is not bad. But surely check your timming too.:devious:

Hey landmizzle, don't you need a fly wheel first. Before you lighten it? What clucth were you thinking of running with your 5 spd. Some hi po flywheel can't be used with a stock clucth. TEP cut thiers down to I think it was 13 lbs? Stock flywheel for the Z's come in two different friction area sizes. The 2+2/ turbo being bigger face wise. But still having the same overall size, wheight as a regular Z flywheel. At TEP they also zero balance the flywheel. :devious:

To all the members of this way-cool club I just wanted to say Merry Christmas and a Happy New Year to all of you. This Is a great place and better bunch of people. With great taste in cars. Good will to all the Z drivers all around the world. :devious:

Ok ZHadMan, yeah your right to much too soon. What about if the members that have the most experience with this electrical Voodoo offer up suggestions on the best ways to get rid of these problems, including maitenance of the bulb contacts. Any problem areas that tend to short out at certain point on the Z etc. Then see if ZHadMan con put in improvements in the original harness that we can all do with add on connecters or other splice in type updates. Such as taking the high current out of the cab if possible with out too much fuss or kacking uo the OEM harness. Better connecters at the outer reaches of the Z's wiring. Etc., etc. Let's see what happens. :devious:

Yeah me to Daniel. I hate my Z. Wanna trade???:devious: I think I just posted on an other thread to you about electrical. Wanna trade?????

Has any body actually looked under the hood of any new car as of late?. Everything is controlled by means of relays. Any given new car is almost completely controled be the ECU with relays. Thinner wire=less load traveling around to burn up. Thinner wire=OEMs save money. but the tech of it is that the ECU controls the component through the relay by means of controlling the ground side. The Ecu grounds the curcuit to be turned on by completing the ground for any given relay. Our system has everything hot almost all the time. This is a Nissan thing. They always used powered switches. Even in the 80's. Daniel I don't think any body is trying to out think those 'O so bright little engineers that come out with this crap so cheaply, because some big wig was pushing hard to rock the automotive market. But your also talking about a company who's motors after the second world war were liscensed to them by British Leyland (or how ever it's spelled).:devious:

I know this post is late for this thread, but for those who see it late like I did. ZHadMan is doing some harness brainwork.:devious:

That's fine for the few who have been lucky. Most 70+% of the connectors on my Z's that I have had problems with, have all been crisp from heat(electrical), melted half off, or melted to each other. When your doing something at a connector, it is always rule of thumb to spray some CRC of the likes in the terminals. But that is not the answer to the root problem.:devious:

Hey ZHadMan, I just want a harness that IS NOT OEM!!! One that works. I don't care that it worked when new. I care that it works now. The OEM has short comings peroid. We should not have to put up with them with the kind of tech we have at our disposal. I want a clean arse harness with good juice and great grounds. When that branches off directly to where it has to and no where else. One that doesn't power the radio from a gauge. Simple, lightwieght, dependable, and easy to work with. As well as up to date connectors, e.g. GM weatherpak, Duesch( I don't remeber how to spell that). I could have already replaced the oem connectors with new ones, but why. The problems inherent to this electrical system will just melt them as well. A harness that works in a different way to do the things we need it to do is what I want. And little by little I will finds good ways to bypass or impove what hasn't already burnt up. But I always figured a simple harness with half as much wiring would cost less than a "Painless". More so if it was a Z lover just doing what he/she could instead of a big company just ripping you off. I don't know. I hate my Z:devious:

I had '72 that came with these locks already on it. Diddn't use this one two much at all. But the key was hard to get used to. Always had to have the right side up. And both the key and the locks where used up. Also only had one key. On the other hand they do look pertty trick when you see them on your car.:devious:

I do Only use one to start out with. But it's better to have the two, each one power only one headlight. This way you can use a five prong relay to power low/high beams and still have higher voltage at the bulbs. Not at the switch. The whole purpose of this is to keep the high current out of the frail electrics of the 30+ year old Z's.:devious:

You know what Brain, my bad. I was thinking F.I. for the clean install. If you huff a carb set up, the blower will set in the valley inplace of the regular intake and be much higher. Plus the carb(s). Hood scoop!:devious: