All Activity

Haha, rabbit hole for sure. Sitting on the bench, with the caliper taken apart in 2 pieces, the brake pads "piston" ought to be able to compress without having to open the bleeder, correct? The fluid should go back the way it came from. Anyway, how hard should it be to move the piston? Can you compress it by hand or do you need a C clamp like I did?

Might want to ask Cody if he had a few parts he wanted to slide in on the Old man!😂😂

Brake line is quite different than the bleed system. IMO go back and do it by having that bleeder open. You might be going down a rabbit hole here.

I can't recall anything like that on my ride, so no idea.

Opening the bleeder when the brakes are stuck will tell you if the problem is pressure in the caliper or something else. If there's pressure in the caliper you can work your way back to the the MC fitting by fitting. Or work your way down, from the MC. First you need to know if it's hydraulic pressure or just mechanical sticking.

Probably worthwhile to read the Brake Chapter. It's not long. Well-illustrated.

But, don't overlook the brake pressure warning switch. Or the NP valve. Can't remember the car. (https://www.classiczcars.com/settings/signature/) It can get gummed up also. Uploading Attachment... Uploading Attachment...

No, I don't think so. But the line was disconnected. It has new rubber hoses, so don't think that's it. The hole in the master cylinder, that creates the pressure when you hit the brakes, is this also the return hole for the fluid?

The Nissan calipers use the rubber seal to retract the pistons. One common cause of sticking caliper pistons is collapsed rubber hoses. The MC can generate high pressure to push through the collapse but the rubber seal cannot to allow the pressure to release. It becomes like a check valve. On some cars the cause is a metal clamp on the hose that rustjacks and pinches the hose. But just degrading internal material can cause it also. I ould guess that a kink in the hose could cause it also.

Was the bleeder open when you tried to push the piston in?

I appreciate all the info. I removed one of the calipers and to compress the pistons, I needed to use a C clamp. Is this normal? Seems like they're awful hard to move. It takes alot of pressure to get them to move one way or the other. So when a guy applies the brakes, then releases the brakes, there's no spring to make the pads retract, they just kinda ride along the rotor. This drag is causing things to heat up and expand, making it tight. Some Fords have springs in the calipers to make them retract. I applied the brakes while the front end was lifted up, it wasn't heated up. After releasing the pedal, there was a more noticeable drag on the rotors. I pulled the master cylinder away from the master-vac, and there was no change. I don't think that's the issue.

I have no clue what those are. Also, looks like you have 5 of them, which is an odd number.

Jim do you recognize that last part in my chrome post? @motorman7 ??

Good to know!

If you can do this when the brakes are stuck it will tell you if the rod from the booster to the MC is too long, causing the return port in the MC to be blocked. You'll have to do it while things are still warm though. Patcon is implying that the air expands as it gets warm creating pressure in the system. They make a tool for setting the booster rod length. It's a fairly common problem, especially with rebuilt boosters. If you stare at the parts long enough you can figure out other ways to get it right.

I believe that’s what he was referring to.

I never had any pushback and I have friends getting work done there now.

I was able to get these out with a small hook. I think the corrosion was holding them in. Once I got it open I found out I have the wrong rebuild kit. I have 46020-C6126, which is for the Tokico . This is a Nabco, which uses totally different residual valves. I think the kit part number is 46011-P6525.

So are you saying it could just be air in the system?

So I received my chrome work today. Most of it looks pretty good. I have a few things I'll ask about. Its expensive work! I have no idea how I ended up with four drivers and two passenger?? Two ash trays 2 sets of visor brackets & three cig lighter rings Four buttons for hatch locks and 2 gas doors I need some help ASAP! Is this a Datsun part?? I'm thinking no...

I would want an early car kit. No split in the rear carpet and different under the seats. Id didn't see that on their site...

If the fluid can't flow back and there's any air in the system they will get tight when driven

I wonder if those bids jump that much because the new bidder is bidding multiple times to clear somebody's previous bid but it only shows a bid when the winning bidder changes?

They did a nice job!! Those latches are tough to get plated well! Ive heard Precision doesn't really want to plate for restorations?

The 7-piece kit, black 80/20 loop. When I spoke to them they said that was better feel than “OEM” and better wearing that cut pile. It does have good feel.