Everything posted by SMW
-
Cylinder Head Removal
At Mike's request, here is a copy of an email I sent to the 240z.org mailing list: A question was asked regarding cylinder head removal, here is what I did with my L24 w/ E31 head: Tools: The specialty tools include a good torque wrench, and a 10mm hex socket for the head bolts. I found the socket for about $5 at OSH. Any place that sells a good selection of craftsman tools should carry it. Preparation Work: One of the time consuming parts of this job is the removal of the air cleaner, carbs, intake and exhaust manifolds, and fuel lines. Lots of liquid wrench is a good idea, along with a good labelling system for all of the wires and hoses. Steps: 1. Remove valve cover and put some penetrant on the head bolts to soak in. 2. Drain coolant (all the normal cautions). Remove the rad hose at thermostat and heater hose at rear of engine. 3. Set to TDC. I like the screwdriver in the #1 sparkplug hole approach. 4. If you only want to deal with the head, secure the timing chain with a block of wood (1/2" thick, 1" wide, ~7" long, tapered at the end) securely driven in to keep the chain tensioner from moving. A good idea is to drill a hole in the block and tie some wire or rope in to facilitate removal. This step is only necessary if you don't want to change the timing. If you are going to tear down the short block, this step probably isn't necessary because you will have to reset timing on reinstall. MSA sells a plastic tool for this, if you prefer. 5. Remove fuel pump. 6. Remove fuel pump eccentric and cam sprocket (note which of the three timing marks the sprocket is set at). Fold excess chain on top of wood block. 7. Remove the two small bolts at the front, between the head and the front cover. 8. Clean gunk out of head bolts to ensure that the hex wrench can fully engage. 9. Now loosen the head bolts in order (to prevent warpage). Start with the two closest to the firewall, then the two closest to the radiator, next two closest to firewall, next two closest to the radiator, etc. 10. Make sure everything is disconnected, then remove head. Don't pry between head and shortblock, this may damage the seal on installation. This set of steps is taken from a combination of Haynes, FSM, and Monroe's "How to Rebuild..." It should be noted that I am not a pro by any stretch of the imagination, and I highly recommend having one or more manual(s) on hand for this job. Others with more experience may also have some tips on this job.
-
rear defogger...
I ran across another option for rear window clearing on the web: http://www.zspecialties.com/hotdeal.htm It is basically a small electric fan and heating unit that runs from the same wiring that led to the wires on the window. I was going to order it, but I'm still dealing with some engine trouble, and that comes first. Might be an easier way to go than trying to locate a small break somewhere in the 30 year old wire. Steve
-
Disposal of Fuel
Hi Mike: When I lived in Corvallis, I think the landfill/dump on Hwy 99 (Coffin Butte?) just north of town had a couple of haz-mat days a year. If memory serves, you could bring them just about anything on a particular weekend. Might be worth giving them a call. Cheers, Steve
-
Air filter for '73
Hey -- small world out there! It sounds like Santa Rosa is the place to find z's, if your find is any indication. Okay, so you most likely have the later air cleaner type. I would guess those holes are towards the very bottom of the cover, facing the engine? If so, (according to the FSM) they are part of a hot air system that activates while the car is warming up and allows warm air off of the exhaust manifold into the carbs until the temp hits 130degF or so and the valve shuts, only allowing air from the snorkel into the carbs. The front hole is where the vacuum motor sits that opens/closes the valve. The other hole is the intake, connected to somewhere (I'm afraid I'm not sure exactly where) on the exhaust manifold via a piece of what looks like flexible heating duct material. As far as air filters go, I'd guess that you picked up one that fits the earlier cleaner assembly. FWIW I have a K&N filter in my stock air cleaner in my '70 240, which fit, but not perfectly. My 260 is still a work in progress, so I haven't gotten around to picking up an air filter for it. For the stumbling, it seems that a tune up is a great place to start. Most folks will recommend swapping in some of the earlier round top carbs for easier tuning and supposedly better performance. I'm rebuilding a set of flattops now for the 260 to see if they are really that bad. Cheers, Steve
-
Air filter for '73
Hi Dale: Wow - 30K original miles, have you had it all along, or was it a great find on your part? A great find either way, I guess. As for the air cleaners, the units are generally carb specific. Does your 73 have the roundtop or flattop carbs? If you have roundtops you most likely have the early air cleaner. If you have the flattops, you most likely have the later air cleaner. The early and late air cleaner units are also visually dissimilar. The early units have round intakes (air horns) to the carbs, while the later units have square intakes. As for the connections, on the early air cleaner the attachments consist of (1) the big (snorkel) air intake, (2) the carb vent tubes, (3) the valve cover vent tube, and (4) the tube from the air/smog pump. I think that's it, anyway. For the later air cleaner the number of connections increased significantly due to the new emissions equipment. If it turns out you have the later unit, let me know, and I'll look up all of the connections in the '74 FSM. Hope this helps, Steve