chaseincats

As a side note, ever since I've had the car - which is going on a decade - it has chewed up/melted the port on the cap where the wire that comes from the coil plugs in. I have a Jacobs Electrics coil on there, could that be why? Pics below:

Glad to hear the cap might be where this issue is coming from instead of the transistor ignition unit or the ecu but I wonder how those teeth got so chewed up

I don't drive it enough for it to be sizable and the cap is a couple years old so MAYBE 1000?

Ok ill grab a new cap/rotor combo

I popped off my cap/rotor today because i got a couple of those small/quick jerks where it like the engine shuts off a cylinder for a second. The teeth look like they're being chewed up and there's scratches on the inside sides of the cap (circled). Could that be it? Also, how does this even happen? Can the car still run well if the rotor isn't pressed fully down? I remember this happened when I started driving the car habitually after sitting for a while but this behavior eventually went away. Here's some images with the problems I noticed circled:

The valve is new(ish) and I know it's not flooding the engine because when I trigger it manually (i have a switch in the cabin) the engine fires right up.

Coincidentally I replaced it maybe 6 months ago because it was leaking and original

The strange thing is it has the hard starting issue if I prime it, but it doesn't have the hard starting issue when I used the clamp to keep fuel in the rail. That didn't make sense to me since its essentially doing the same thing...

Fair point - will do

There shouldn't be an issue with the pump since it is brand new but couldn't hurt. Could you take a picture of how you have the hose routed to avoid the potential of it rubbing on the axel?

Right, I was curious if the FPR was letting fuel bleed past and into the tank, so I clamped the line that comes after the FPR in the same way as I tested to see if the car was losing pressure after the fuel pump, so I clamped the line that heads into the fuel rail

The FPR is good. I tested it by clamping off the return line (the hose that comes out of the lower outlet of the fuel rail) and let it sit overnight. The car had the hard start issue. I then instead clamped off the inlet hose (the one coming from the fuel pump) and the next morning the car started without issue. That is how I determined how to test which item is not holding fuel/fuel pressure when shut off.

I remember the ideal way I saw was to loop the hose up and over one of the metal things under the car (working on this was so long ago i don't remember what 'metal thing' it was) but that ended up making the tank line angle like this: /-\ which hindered fuel flow. Could you take a picture of how you have yours routed?

The wrong fittings meaning the clamps on each hose? This is the setup that I've had on there for a decade so it's odd its having this issue now that I changed to new hoses.

Do you have a link to that part (or the hose sizes) and I'll pick it up? The one I have is the same outlet size on both size which is why the larger hose slips over the tank one with the metal piece in the middle. Also besides the zip tie I added, how did these lines used to be held up?

Fair point, I'll give it a shot. As a side note, with the tank house outlet and the fuel pump inlet hoses being a different sizes, the PO had a metal cylindrical adapter that he popped into the tank hose side, put the fuel pump hose over it and clamped it down (this is of course on the low/no pressure side since it is just where fuel flows down into the pump from the tank). The car has always been setup like this and that joint has never smelled like fuel - but I was always curious if using an adapter like that is how all 280z folks overcome this issue. See below picture for what I'm referring to - you obviously can't see the metal adapter since it is inside/covered by the hose. The ziptie is there to hold the fuel line up.

It's standard auto parts 'buy by the foot' stuff. It's standard hose, not EFI hose if that helps diagnose the habitual hose clamp tightening issue.

I've put new lines back there and tightened the clamps a handful of times. I've really had enough of trying to find the air leak back there...

The frustrating thing is they are new air lines.

It says on the amazon page it will hold a max of 87 psi - doesn't the pump push ~40? The air leak is back near the fuel pump, that's why a check valve in the engine bay was able to hold pressure I believe.

That's perfect, thanks! I talked to one of my friends about it this morning who is an engineer of some sort and he said what is probably happening is a tiny amount of air is getting in the line from somewhere which is letting the pressure out and allowing it to flow back to the tank (like a straw with a tiny tiny tiny leak. That definitely is happening because when I pressurize the line there is a VERY faint fuel smell from the back, and I have to keep tightening the lines. It's so weak that I finally said enough - give me the check valve. I don't understand why the lines keep getting mushy enough to allow that to happen but as long as its so faint, it should be fine.

Hi all - Great news - after a very long time of chasing lead after lead, I've finally found the culprit for my hard start - gas is flowing back to the tank, oddly through my new fuel pump overnight. I ended up putting a clamp on the hose that sits between the fuel filter and fuel rail, waited 24 hours, then cranked the engine and it started right up. The odd thing is if I manually trigger the fuel pump to pressurize the rail, then crank the engine, it still acts as if the rail is completely dry - which is confusing to me since the clamp method noted above is in theory keeping fuel in the rail in the same way as priming the rail by manually triggering the fuel pump would be. This is the pump I have on it now - don't all fuel pumps have check valves or are they external and I simply don't have one? I'm planning on splicing this check valve between the filter and rail (where my clamp was) which should work I'd think, or is there a better way of going about this?

Wow so the flappy bit is supposed to flap around when closed it seems

Hi all - Inside my 78's center console cover is a rectangular piece of metal that flaps around along with another piece that looks like it pops into a small hole but won't line-up to fit. Below is the flapping piece I'm talking about along with a quick video I made which should be of more help. The video is here. Curious what this is for, how to connect it, and if I am missing a piece to do so. Any ideas? -chase

Understood, thanks!