Zed Head

Those are CV joint half-shafts and they're most likely too long to use, in addition to needing an adapter. The parts from the R180 in your car now might swap over, I believe. No idea on the details.

I compared dimensions on the OReilly Auto web site and the rears are 1 1/4" longer of the two choices for sale there. Everything else is the same. So if you have fronts you might run in to a length problem. Rears should be at least 11 inches long according to their page. Brake Hose - 1973 Nissan 240Z | O'Reilly Auto Parts

Now you'll need to check the engine for termites. That L28 is looking more enticing. I see that you stuck your wedge back in. It may be too late though, the tensioner is spring-loaded to get it started on the chain with hydraulics for running. When you pulled the old one out the tensioner probably popped out of its hole. You might not be able to get the sprocket re-installed, if you planned to re-install the head without removing the front cover.

That is a wedge that's used to hold the timing chain tensioner in place. It's described in the engine tear-down procedure in the FSM. If you had planned to only remove and re-install the head, you would have inserted that before removing the head. Not uncommon for people to forget about them and re-assemble the engine. Someone has had the head off before.

I would get the L24 running then take it out and run it hard to blow out the crud, wear down the rust, soften up the seals, etc. Some people call this an Italian tune-up (I think the term references the cars, not the people, no offense intended). Not much to lose except a towing fee and you might find that it's actually in good shape. A little bit of surface rust in the cylinders would probably kill your dry pressure readings.

You won't see any frowns (unless you can't stop talking about it) but there won't be much interest either. Hybridz is the swap site. The site names tell the story, classic and hybrid. Pretty simple.

Check for power at the switch on the brake pedal. If it's there, the problem is after the pedal, if not it's before.

FastWoman's suggestion in Post #7 is most likely the cause. Commonly called the "hot start" or "heat soak" problem (NOT vapor lock). Very aggravating and common. Many people just learn to live with it. I've done some experimenting and have found that directing cooling air at the injector bodies will stop the problem. Nissan did the same with the 280ZX, but installed a fan and ductwork to cool all of the components of the fuel supply system on top of the manifold. Heat from the engine block and manifolds heats up the injectors and fuel rail causing the problem. Many theories have been proposed but they all boil down to too much heat. 20 minutes seems like the point where things are the hottest. Earlier than 20 and the heat has not transferred to the fuel system, later and everything has cooled down.

check dimmer switch. its part of turn signal stalk click back and forth

Post #71 and 72 kind of covered the dual pickup issue. The stock ignition module will work fine with one pickup, it just won't use the other ignition circuit. If you convert to a GM HEI module, you will only be able to use one pickup. In #72 I got the impression it didn't matter anyway.

You might be able to use a meter to measure voltage at the plug to see if you have a gauge problem or some other problem. I don't think that you can reach the adjustment with the gauge plugged in. Good luck on the fuel gauge, my tank has never been completely empty so I don't know how low the needle goes. I didn't think it went that low with power to it though. I wonder if you don't have the volt meter wire running through the fuel sender circuit. The resistance would lower the voltage. Wire colors are lower on the page that the drawing came from, BE-35.

You probably can't see this from your phone. They're under the hood.

Still not clear what AZ was testing. Your posts aren't clear. But your voltmeter readings look good.

Check the fusible links. One of them is for the headlights but may also power the running lights. Or, if you have a voltmeter, check for power at the fusebox at the headlight fuse. If you have power at the fusebox then your combo switch is working but the dimmer switch might have problems (not grounding). If you don't have power at the fusebox, then check for power at the fusible link. It might still have a label on the side that says "HL".

Seems like the test results are on the old alternator, not the new one, right? Hard to tell. The regulator regulates, the alternator charges, so yes, you can get high voltage from a bad regulator. The extra wire might be for the "P" terminal. Some later cars apparently use it for a 6 volt supply or something like that. There would be a "P" cast in to the housing wherever the wire attaches to the alternator. Your 78 car wouldn't use it. On the "15", the voltmeter's in the car aren't very accurate. Use a meter under the hood. 14.8 +/- a couple of tenths is normal, with the RPM up a few hundred above idle speed. All of these alternators typically put out barely enough voltage to run everything at idle speed. The best way to make sure everything is right is to measure at the battery or alternator terminals with a good voltmeter, revving the engine until voltage stops rising to make sure the regulator is regulating. There were probably instructions in the box the alt came in.

I thought the engine might still be in the car. Yes, the starter mounts to the transmission. Probably an N47 head if you have a white exhaust port. And that must mean the manifolds are off. So you could look for deposits on the intake valves or oil leaking down from the guides. White is good on an exhaust liner, that means it wasn't overloaded with fuel and oil deposits and was staying clean as designed. Too bad you couldn't take and post some pictures so the experienced eyes out here could take a look.

Watched your video and the first thing I noticed was the white gauge faces. So it's been taken apart and re-assembled. At least the needle moves. There is an adjustment screw in the back of the voltmeter (not ammeter) that will set the starting point for the needle. I would guess that somebody turned that screw (a lot) when they were taking the gauge apart. I set mine to sit at 12.6 volts with the engine off by trial and error. Plug the gauge in and note the reading, unplug it and turn the screw, repeat. I notice that your fuel gauge doesn't seem to work either. Gauge wiring is shown in the FSM's Body Electrical chapters.

I would say those numbers are pretty meaningless, but at least give hope. Probably not bad for wrench speed RPM. Can't you borrow a car battery and jump it? You could even disconnect the starter from the car and jump the starter directly. You can tell a lot by looking if you know what to look for. How did things look? Broken manifold studs, sludge under the valve cover, spark plugs from the L28 (this time), etc. They can tell you something about how the engine ran before the car was parked.

Oil fouling is a bad sign. Valve seals or rings could be bad. You won't have much time to tinker with the old 240Z engine if you're trying to get the L28 to stop smoking or just run right. You might keep looking. My old L28 had bad valve seals and would only run well after a high RPM run to burn off the crud. Otherwise it just ran "okay". The cylinder pressure numbers were great, you couldn't tell the seals were bad by that test.

List the order in which you did all of the things in Post #1. Can't tell when you replaced the fuses, before or after the starter change, for example. Did you disconnect the battery before the starter change or try to get by with being very careful? Also, why did you change the starter? Maybe it wasn't the problem.

downloadthemanualandcheckthewiringdiagramherehttp://www.nicoclub.com/FSM/ When you get to a computer. The files are probably too big for your phone. Using the internet from a phone is difficult.

Here's a link to the new seller of axles for the Subaru diff swap. Johnc, a forum member here, developed it over on hybridz.org and it's pretty popular. Tranny & Rear Diff Parts For what it's worth, I noticed the difference between a 3.54 and a 3.9 in my 76 Z with a later ZX 5 speed (3.062 first gear ratio). It really depends on your driving style. If you're a clutch-slipper, you might not notice, but if you're a clutch-saver you probably will.

It sounds like your timing marks are not aligned with the #1 piston being at top center on the compression stroke. That's what you should check next. The timing flashes aren't worth anything if the marks aren't correct. If I was in your shoes I would pull the valve cover, rotate the engine until the #1 cylinder cam lobes come up (compression stroke), and stop when the timing mark on the damper pulley is at zero on the indicator. Then see how close the timing sprocket notch is to the oblong groove on the camshaft retaining plate. If they are aligned, you could assume that the timing mark is within about 8 degree of correct. Whatever the reason that the timing flashes that you're seeing are not working with the marks and indicator, a new distributor will have the same issue. I've also seen my timing light pick up the next wire over's pulses. But your problem sounds more like a bad damper or screwed up timing marks. OR, considering that it's not your car and have no idea what's been done to the engine, and this statement, "Good news is he says it has the bottom end from an 81 so higher Compression.", it might just be that somebody has built an old-school 12:1 CR "race" engine and it will never run with standard timing. Overall, it might just be time to check the basics of the engine; cylinder pressure, confirm correct timing marks, check camshaft timing (notch and groove), etc., to see how much farther you can go.

I've always thought of "static" as meaning no advance mechanisms in play. Basically idle timing. Maybe I misunderstand the terminology. Anyway, if the car runs and you have the timing light connected to the #1 cylinder wire and you're getting a steady light just in the wrong place, it won't matter which distributor you have installed. The timing light just tells you when the spark happens in relation to cylinder position. The engine will run the same way at idle with any distributor and module that's producing spark. These engines will run, sounding like tractor engines, if the spark plug wires are installed in reverse rotation order. Backward. Worth a double check. They probably like different timing in reverse also. At least it's running well enough to know that you have a timing problem. You've made it quite a way from "fuel pump help".

Is this the Z Car Source distributor? Good to know for future customers. They're going to give a refund, right? As far as timing, if the engine is running you should be able to set static timing. The vacuum advance should be on ported vacuum and the idle speed should be below the start of centrifugal advance so nothing should be changing at idle. If you had bad springs and an advance weight flopping around you might get jumpy timing though. You'd have to pop the breaker plate out to see that. On the ZX distributor swap - it is simple to do but if your customer wants to retain the car's original functionality you'll need to stick with the stock ignition module and distributor. 1976 Federal models have two pickups in the distributor and two circuits in the module, to bump timing up when the engine is cold. I don't have it on mine anymore and barely notice a difference but it can result in about a minute of lower than normal idle speed while warming up.