2ManyZs

How many sets do you want? 14x6 only or are 14x5.5's OK?:classic:

Guess I better start collecting all the ones still being used on race cars and corner the market. Hmm, that might not be a bad idea after all.... Only problem with the set I had is they were 14x5.5's.... but they did look good on the 82 200sx I had at one time...that's the reason I traded them back to the guy who had them originally so I could get the factory rear bumper panel back that I traded to him for... whatever it was that I can't remember.... But in all seriousness, there are still plenty floating around if people know where to look. They just aren't being used. Be willing to bet most are like my old set, just sitting in a shed somewhere. Roadster and 510 owners probably have more than all the Z nuts combined as they were a popular swap. Of course, they were also a popular race wheel too, which won't help in the looks department.

Guess I better go get the old set I had at one time... silly me, I didn't realize they were made of "unobtanium" like this set.. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=40017&item=2439076314

Have you ever had the gas tank out? Since you've eliminated most everything else, could it be the tank straps are loose? Or, if the tank was out, were the small pads on the top of the tank OK? Perhaps the cushion pads have detiorated and the tank is moving inside the tank straps? Only other things I can think of is the exhaust hitting the diff crossmember or the diff itself and it only sounds like it's coming from the other side by transferring through the chassis.... One other off the wall idea... the mounting bolt on the bumper end? Guess the frustrated smilie would be a combination of these.........:cross-eye :tapemouth

I don't know if they'd have the right alignment tool, but they could probably get it. MSA has them for sure. As far as the clutch itself or slave or master cylinder, they should be able to get them as well. Since it's a street car, there's no reason to spend extra money on a clutch when a stock replacement will work as well.

I'd have to vote original as well, but with a few differences. If you want to do a few simple bolt on mods that can be changed easily I don't see why that would hurt either. Things like wheels and tires, and other things such as air dams that can be bolted onto the car without modifying the original body or chassis. Just as long as you can change it back without having to resort to filling, body work or buying new parts to replace door panels etc.... Few enough cars are 100% original, but to "personalize" it to suit your tastes if it can be put back original in a matter of an afternoon or two would also be fine in my book.

Don't forget the most important tool, a clutch alignment tool... saves a lot of time and aggravation if you get the clutch disc aligned right the first time so the trans goes back in on the first try......

Depends on how difficult you consider pulling the transmission to get to the clutch is.... it's not the worst job, but it's not that easy either. That is, if it isn't the master cylinder or slave cylinder that is causing the problem.

Sounds like either the clutch itself died, or either the clutch master cylinder, or slave cylinder might have given up..... Double check the fluid level in the clutch master cylinder, and if that is OK, check that the slave cylinder has travel when someone else depresses the clutch. If that has a good bit of travel and looks to be working OK, sounds like the pressure plate may have given up. You didn't do it... old age did.....

The last time I checked, you could still get these from ZeddFindings. You might also check with Midwest Z and see if Chloe can source them as well. I got mine from www.nismoparts.com a little over a year ago for about 129.00 each... but haven't kept up with the going prices since... Sometimes people on Ebay "stretch the truth" just a bit to inflate their prices.....so double check with all the Z parts supplier before you pay that much. Kinda like the set of restored Libre wheels I saw this morning with a $1600 Buy It Now or the complete "rare" 72 intake and carbs they are asking 250 bucks for....

Mine has the same thing, it's factory. The only place on a Z that didn't get a spot weld is what you pictured. The ones over the T/C mount look better than the ones that were one mine that's for sure. I've seen some that hung down an inch.

All I can say is, I don't remember ever seeing one like that in the US... looks like it's shaped like a "spook", just longer. Must be something made in Australia.... or Japan?

A "half moon" box end probably would work pretty well... might be a better idea than using a cheap box end and end up with rounded off nuts.... Hmm, too bad all my half moon box ends aren't metric... guess I'll go look on the Craftsman site and see if I can find one..

Funny thing about both those pics, is how much it reminds me of the Ferrari Maranello in a side shot.. and probably more than one Ferrari at that... It's kinda funny how many people put body kits on a Z to change it's looks, yet this is probably the first time anyone has ever made a kit to make another car look like a Z....

Only thing I ever saw in Aiken, SC was the W.R. Grace mine....:tapemouth Picked up a lot of "dirt" and took it to the Manville plant in Laurinburg, NC so they could make railroad brake shoes with it... try going into that place when it's 99 degrees out and come out clean.....:cross-eye

If the nuts are on the backside of the diff flange and not inside the driveshaft yoke that ought to be easier than the nuts being on the inside of the U-joint yoke. The studs should be in the diff flange and not the drive shaft if I remember right. Only way I've ever been able to get the nuts off is with an open end wrench about a 1/4 turn at a time until they loosen enough to get them off with your fingers. If the nuts are on the inside of the U-joint cavity, turn the driveshaft so the bolt is at the 6 o'clock position and do one at a time. That opens up the cavity as far as it's gonna get. Oh the most important thing, don't use a cheap open end wrench or you're gonna round them off.

Wonder if the conversation at Mark's dinner table tonight was about moving south, or southwest....

texasz don't feel bad, mine is an 11/70 and our Vins are 6533 apart.... guess they were really cranking them out by then... over 2000 a month. I just wish I had a four digit VIN...

Before you decide you ought to run the car through a car wash just to see if the T-Tops leak... If it weren't for the shoddy repair jobs it wouldn't make a bad "parts-chaser"..... well, unless you really don't want an automatic that is..... Judging by the similar cars on Ebay, they don't seem to have a lot of interest in the 82-83's unless they are Turbo's....or at least that's what the bids reflect. I'm not even going to hazard a guess on what it's worth....but considering there's an 82 on Ebay with a 5 speed and some rust showing and no bids at a starting point of 2K yet.... And if you could get it for a really low price, you could always use it to donate parts like the disc brakes and maybe the engine for your 280 if you wanted too....shame it doesn't have a 5 speed....

My first guess would be a wiring issue somewhere between the dizzy and the coil possibly.. the abnormal tach reading points to an electrical problem somewhere in that area since that's where your tach picks up its signal. But then, I'd be just guessing since electical problems stump me worse than any...

Doing the floors is a labor intensive job, which means, even if you have the welding ability and the tools, the job will require patience and working slowly and accurately to do the best job. Probably the worst part of the job is taking off the old tar mat off the stock pans so you can see what you really have to work with. One word of caution I would like to say is don't cut anything out of your floors until you get your replacements. Not all the replacement panels are the same. The best ones from ZeddFindings and the Premium pan kits from MSA are identical as they come from the same place, however, if you get the cheaper ones, there may be a lot of small differences in them. It's always best to cut out your old floors using a pattern off the new replacements. Remember, you can always trim to fit, but to fill in holes, you're gonna be doing even more cutting and fitting, welding,etc....

The 89-94 240SX caliper is what Modern Motorsports kit is designed for, although, I don't know if the caliper bracket is the same as the one for the 280ZX caliper. They might be similar, but I don't know if the 280Zx caliper and the 240SX caliper will bolt to the same bracket, such as the Maxima bracket. The 240SX caliper is what is recommended by many as the pad area is a little larger then the pad in the ZX caliper and the E-brake hardware is easier to hook up. I found a set of reman 240SX calipers on Ebay for roughly 120 bucks. Not cheap, but not all that expensive either. Now all I need is the bracket and rotor and I'm all set.. one of these days..... If I'm not mistaken, the 84 300ZX rotor is slighly larger in diameter than the 280ZX rotor....

Well, I can't seem to find the diagram I thought was posted somewhere... but I did find this thread on HybridZ. Seems no one likes the one wire GM alternator and most prefer to use either the GM internally regulated, 280ZX internally regulated, or the Maxima alternator in their Z's. If you read through the thread, maybe something will sound familiar with something you may have in your car. http://www.hybridz.org/phpBB2/viewtopic.php?t=305&highlight=gm+alternator

I think the part that has people afraid to hazard a guess on what could be wrong is the fact you've had so many things happen at once that the problem could be most anywhere.... Did you do the single wire GM alternator conversion according to a wiring diagram? I know I've seen one somewhere for the conversion, but it might take some scrounging to find the right site again.....:stupid:

Here's the link to MSA's 70-74 air dam page Mike, they might have some different ones if you try the body kit page as well. Those would probably be the Kaminari's and Xenon's though. I kinda like the fiberglass valence with the small lip at the bottom, less likely to get hit on something and crack it as it doesn't sit quite as low.... Take yer pick..... http://www.zcarparts.com/store/merchant.mvc?Screen=CTGY&Category_Code=7AD1