Matthew Abate

What did you torque yours to? I couldn’t find the torque spec in the FSM so I went with what is in the Chilton, which is 43-54 pounds. I’m thinking that might be part of it. As soon as I can I’ll pull a bolt and check the measurements to verify that.

Got the hubs and rotors together... ... but... ... notice anything? The hub bolts are protruding. They will hit the wheel if I leave them like that and prevent a solid mating surface between the hub and wheel. This could mean one of, or a combination of, three things: the new bolts are longer than the OEM bolts, the new lock washers are thinner than the OEM lock washers, or the new rotors are thinner at the mounting point than the OEM rotors. I’m going to pull a bolt and double check the length as soon as I have time, but I suspect that it’s the rotor. They have a recess where the bolt hole is and I think it’s too deep. If the new bolts and washers are the same measurements as the OEM bolts I’ll have two options: grind the bolts shorter or find thicker lock washers.

I got about half way and ran out of vacation days and sand, so Blast Lab finished it. Sent from my iPhone using Classic Zcar Club mobile

It’s been a while since I posted progress, so I thought I would throw some photos up: Note the helicoil that came out with this bolt: Time-sert installation: Finishing: New bearing cups in: Body status: Carbs back from Z Therapy: Hoping to have the rotors and hubs on the struts by the end of the weekend. The weather has been hot and humid so I’m not certain the paint will be cured on my dust shields by then, though. After that is scrounging up the hardware that holds the suspension on the car, getting some cheep tires on the old mags, and getting the suspension out to the painter after the undercoat is on.

Got a lot going on, which I will post up when I finish, but in the mean time I have a question. I almost started a thread for this but I melt like I should ask here first. I am planning to spay ceramic sound deadener, heat shield, and undercoat on the car. My question is where would you guys put these? The painter suggested: • heat shield just on the firewall and over the forward part of the transmission hump, inside the cabin • Sound deadener inside the doors, on the floor inside the whole cabin, and inside the roof • And undercoat under the entire car stopping where the transmission jump bends and you can see it from the engine bay, as well as inside the wheel wells and the inside of the front fenders. I am not super knowledgeable on these three things and totally willing to entertain suggestions on changing this. Please hit me with what you think is optimal. Remember this is a resto-mod, so I am going for function driving form, not historical accuracy. Sent from my iPhone using Classic Zcar Club mobile

Bummer. Maybe I’m just overtightening it. Sent from my iPhone using Classic Zcar Club mobile

Can anyone recommend an alternate gland nut to the ones that came with my illuminas? I’m not happy with how soft the metal is nor how thin the edge is where the wrench grabs. I’m seeing some rounding and I haven’t even tightened them that hard. The ones that were on the car before won’t work. They were mismatched and in terrible condition.

Great! Thanks. Sent from my iPhone using Classic Zcar Club mobile

Does anyone know the size of the lock nuts for the ends of the spindle pins? I want to get some that aren’t locking to temporarily hold everything together, which I would replace with the locking nuts later. I had been looking at these 12mm 1.25 pitch ones but I’m not sure that’s the right size: https://www.boltdepot.com/Product-Details.aspx?product=6878

Back on track thanks to Captain Obvious and his buddy Gary. Thanks Bruce! —- We identified the problem(s). They had pressed the inner bearing in at an angle and then forced it down. This did some gnarly but repairable damage to the inside of the hub and is why the bearing was uneven and destroyed. They also screwed up my spindle pins and all the hardware that went with them. I have new hardware on the way. The spacers Jim K sent me were perfect and went right in. Everything is now back together (minus the drum brake backing plates) and ready to continue, but first I’m cleaning up my paint.

Looks great! Did you trial fit the header? I’m trying to find out whether the Fujitsubo one has the same fit issue around the steering as the Spirit Garage header and don’t see it in this thread. Or is the header unchanged?

Side comment: I was thinking about the issue with the header interfering with the steering and was wondering if anyone has investigated using the Trust GReddy TR NA Ex Header with one of these exhausts. Supposedly it is bolt on with no mods needed on LHD cars. Whitehead Performance offers it for $648 and recommends the Fujitsubo exhaust for it. I’ve seen people mention pairing with with the Spirit Garage exhaust, but I don’t think I’ve seen anyone actually post pictures of this set up or write up a review. You can also get it from Revmatch for $623. If I had to pull the trigger on an exhaust setup right this second without a chance to do any more research, it would be this header paired with a Spirit exhaust, just based on forum comments (bolt on, fits around diff, tucks high, looks period correct, well regarded manufacturers, sounds good, not insanely expensive). I just wish Trust made it in stainless. I am digging deeper on the full Spirit Garage system, though. If the handful of fitment things mentioned aren’t too onerous and I can find it for less than RHD wants maybe that’s a better choice. Again, it would be cool if someone who understands this and can be objective put together a sticky post doing a compare and contrast with links and dyno charts off the same car.

None taken because that’s the plan, and also it was a shop that messed up.

Yeah, when everything was together it was shy of coming all the way through, so the flange was putting lateral load on the inner bearings when torqued. The shop wanted the spacer shorter to get the bearings closer together. Sent from my iPhone using Classic Zcar Club mobile

Yet another example of where I only half followed my father’s advice. I went with the lowest imperial measurement but did not check it against the lowest metric measurement. (Edit: no need, they are the same when converted). I think my plan now is the freeze the spindle and warm the outer bearing to 120 degrees, press it on myself with my floor jack hacked together home made hydraulic press, then freeze the inner and do the same. Taking these parts to shops is only giving me grief. Sent from my iPhone using Classic Zcar Club mobile

I’d love to see someone compile all of this info into a sticky... hint hint. Also, Sean, you said you had a theory on the benefits of twin pipes a few pages ago. Let’s hear it. Sent from my iPhone using Classic Zcar Club mobile

Yes, I agree. And yes, zKars saved my arse again. The last question I need to answer out of this mess is did torquing the nut to 181 pounds like the FSM says crush my brand new OEM bearings or was it the idiot who ground my spacer? The shop insists the Chilton manual is correct at 28-32 pounds and pointed to the F-350 spec of 110 pounds as a supporting argument, but they also ground down a NLA part by hand, so... Sent from my iPhone using Classic Zcar Club mobile

They are type B spacers. You can see the amount of material removed here:

NLA. They just haven’t updated their site.

Update: all parts retrieved. I will asses them tonight and post a picture of the damage to the spacer. The hubs say B but I haven’t checked to see if the spacers match. Regardless I have one that is messed up. Sent from my iPhone using Classic Zcar Club mobile

Not sure which letter yet. I need to retrieve everything in the morning and find out. It’s not the same shop. Right now I have three of the five shops I’ve gone to in my area in my black list. The end basically has been held against a grinder so it has a slice taken out of it that’s about .25-.5 mm deep and maybe 15-20 mm wide. It’s not the entire face that mates to the bearing but it’s not just a nick. From what I can tell Motorsport is selling refurbished originals. They’re charging a core fee. Edit: the reason the guy took a grinder to it is he felt that it was too long and the spindle wasn’t coming all the way through. He thinks the shoulder of the spindle should pass through the bearing so that the copper washer (which is an optional part) sits in the spindle rather than the bearing. I think the entire problem was started by the washer. They’re also telling me the FSM torque spec of 181# is wrong and the Chilton spec of 22# is right.

Motorsport wants $50 each plus shipping. http://www.thezstore.com/page/TZS/PROD/classic01a/23-5031R Can anyone beat that? Edit: they only have the B version, so I need to find out which one I need from the shop. Actually, I need to get all my parts back and go somewhere else.

So the local shop that pressed my rear hubs together messed something up and I had to take them back. Not only do I have to replace the bearings, they tried to grind the spacer to make it shorter. Anyone have one I can buy? Sent from my iPhone using Classic Zcar Club mobile

They are NLA. If no one here has them I’m out of luck. Sent from my iPhone using Classic Zcar Club mobile

I had a local shop press my rear hubs together and had to take them back because the bearings weren’t seated correctly. The idiot working on it tried to grind down the end of the spacer to make it shorter, so now the end has a gouge out of it. Do I need to worry about this? If so, how can I find a new one? Does anyone have one to spare? Thanks in advance.