Zed Head

It will only happen when the problem is happening. The module gets hot and starts firing the coil at a higher rate than designed. Extra sparks out of time, and extra fuel because the EFI is controlled by spark. Let the module cool down and it works properly. Mine would do it whenever I got above 3000 RPM. I could cruise around at low RPM, get on it, and end up having to pull over and restart. The tach would show 4000 or so when I knew it was only about 2500, plus it was quivering and jumping around. Just clues to look for.

There was a statement earlier about affecting something when you changed the alternator. So, next time, if you try again, you can do some testing before swapping. It might even be enough to just wiggle some wires.

Seems like the basic questions is - do you have the proper voltage at the S pin, and is the S supply consistent during operation? The problem is overcharging. You can run a completely separate jumper wire from the battery positive to the S pin and see what happens. If things start working correctly then you can get in to the harness. If they don't then the alternator has a problem.

Edit - didn't see the title, it doesn't show when you read a post. Putting the details of your car in your signature makes it easy and consistent from post to post. Good luck. Can't tell what you're working with, looks like a 280Z, by the picture of the engine. Your problem description fits a failing ignition module pretty well. Does the tachometer needle behave normally while the engine is acting up? Or does it jump around and read higher than it seems the actual RPM are?

Here's a cheap alternative. https://www.oreillyauto.com/detail/c/standard-ignition/fuel-delivery/fuel-injection/pressure-damper/3ef9efd721d3/standard-ignition-fuel-injection-pressure-damper/std0/fpd84?pos=23 Compare to others. https://www.oreillyauto.com/shop/b/fuel-delivery/fuel-injection/pressure-damper/3ef9efd721d3

Maybe just saving some money? Didn't have spare hose or tubing? Had a spare FPR laying around and needed to stop a fuel leak so he could sell it? There was a thread in the past about alternatives. They're out there but if you go to the Z specific web sites, that looks like a quick and dirty good idea. https://zcardepot.com/products/fule-injection-pressure-pulse-damper-efi-280z-280zx

ZCD has stuff. https://zcardepot.com/collections/fuel/products/fuel-line-pump-to-engine-stainless-steel-280z-1977-78

Fuel won't flow backward through the FPR. It's pushing on a tiny little area. Hydraulics.

Maybe just spanning the gap between the old crusty hoses ends. Looks like a new FPR though. Strange. @zspert, that old braided fuel hose could blow, or just slow leak from longitudinal cracks, at any time. It's on the high pressure side. I remember that soon after I bought my car, after I had installed a new pump and got the car driving well, I was pulling out of my neighborhood and a UPS truck driver pulled up beside me to tell me that fuel was pouring out from under my car. A PO had used low pressure fuel line and it had split. Luckily everything was cold and I was within walking (running) distance to my house where I had some spare hose. I was able to squeeze under the car which I had parked next to the curb behind a strip mall to replace the hose and get it back to the house. I felt bad about the big gas stain on the pavement but at least there wasn't a pile of melted plastic and tire rubber.

Many people don't really understand what the sealing surfaces are in a compression fitting. It's important the surfaces are clean and that the tube is round, not distorted. It could be also that the Nissan 8 mm nominal tubing dimension is just not right for the typical US domestic automotive repair kit. Things to think about. Good luck.

Could be a check valve to make up for a bad one in the pump. What is on the fuel rail on the engine?

Did you guys use a ball hone? Looks scrapey. The angle seems shallow like it wasn't moved up and down fast enough. Not an expert. You can still see the scratches. Don't have the experience to say if it will seal well with the scratches but it doesn't look ideal. I think that you're on the edge of "go cheap and hope" or spend the money and do it "right"? If you have the means of tearing it down again easily, I'd probably just put some new rings in it and see what happens. If you have limited space and time maybe you should spend the money and make sure it's right. It's a dilemma. Another way to describe it - if you like working on it do the rings and take a chance, if you like driving it spend the extra money on an overbore.

I was going to suggest strapping the ramp to the wheel with a bungy cord. An old inner tube under the ramp might work too. You could even glue it down.

I'd use the scissor jack under a control arm then set the ramps under the tires and drop it down on them.

Anybody notice this one go by? If you're gonna modify, modify bigly. https://bringatrailer.com/listing/1972-datsun-240z-273/

It might just be loose. If you just had a pinhole in a line the metal repair tube that you have now would be what I would do. The line that you have might have a bad flare and that's why it's leaking. The correct way to use a hose would be to put a bubble on the end, like on the transitions from rubber to metal on the factory metal line. Site's idea was good, I'm just saying that all solutions should be done correctly. Kind of depends on your tools I guess, I had flaring tools so I reflared when i was working on my fuel system. I've also used compression fittings, which might actually be what you already have. If so, you can just crank it down to make it tighter. The PO probably couldn't get the leverage on it. Good luck. Here's a typical repair kit with a compression fitting. https://www.napaonline.com/en/p/NOE7304932?impressionRank=11

Something I've been able to do with brake lines is to detach the line from where it is fastened to the body. Then just flex the whole section out to where you can work on it. I did that in the front so that I could pull the MC without disconnecting it. It looks possible in your case. I see a screw head.

In 79 they went to the more sensible labelled drawings. Odd thing though, they dropped down to 25 - 36 in 79, then in 80 went back to 44.

Probably right. I overlooked #4. Sorry about that. The nut actually attaches the bushing sleeve and washers to the rod and the rod to the body. Not the transverse link. That's what got me. Still seems like a high value for a fine (higher leverage) thread pitch. But it is an important piece. They carried the weird words all the way through 1978.

Never mind. Nissan's odd writing got me.

Edit - I found them, thought they weren't there. Hard to find, I had to search for the word to get the drawing number then look at the drawing again. One of the 5 speed balls has (1/4) after it, don't know what that means. Glad I'm not rebuilding any transmissions. Edit again - I notice that ball #66 has a different part number. Any chance you put a small ball where a big ball should go? https://www.carpartsmanual.com/datsun/Z-1969-1978/power-train/transmission-gears

Seems like they just want to make sure the "washer" (l'd call it a spacer) spins with the shaft. Edit - obviously. Might be that any dimensional differences across the "washer" could cause some weirdness if it moved. Funny, but the 5 speed has more of those balls than the 4 speed even though, supposedly, the 5 speed is just a 4 speed with an extra gear. Actually, a lot more differences than I thought. Edit - looks like 4 speed shafts might not work for 5 speeds and vice-versa. The washer you're looking at is 21?

I have the wiring diagram for one of these. It has about eight positions. I don't know much about them except that the wiper motor must be getting a lot of amps on high speed based on how fast the blades move.. They're fast. Actually the ancient Z motor and mechanism would probably hold you back on upgrading the system. Are you going to design a simple harness to make it plug and play? Looks like fun. https://www.ebay.com/itm/265485270180?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=pCKhnAvpQCe&sssrc=2047675&ssuid=&widget_ver=artemis&media=COPY

Actually, since it's open, some Scotchbrite, gasoline, and a rag will let you take the critical measurements. I thought you were just going to break it down in a garage and run a ball hone through it. Why pay to get it hot-tanked if it's not what you want? You'll be removing that protective film of oil and grime for when you put it in the back yard for storage.