lm71z's Content - Page 3 - Classic Z Car Club Skip to content

lm71z

Community Member
  • Joined

  • Last visited

Everything posted by lm71z

  1. It usually runs steady at slightly below half on the temp gauge. I can tell by just touching the engine after it's been running that it's running hotter than normal.
  2. Today the temperature gauge on my 240z is running slightly over half. I swapped out the valve cover yesterday for a polished one, but I don't see why that would have caused any problems. The engine is not leaking any oil whatsoever and it's not low on coolant. Nothing has changed except for the valve cover and I have no idea why the car is running hot. Any ideas??
  3. I just checked with Nissan and the numbers for the choke cable for my year 240z are not available. Will the assemblies for later 240z's work with my early 71?
  4. Actually, my 240z is called a 1971, but it was really made in december of '70. Can you give me the part number for the earlier choke cable? And, under what category in the diagrams did you find the choke cable?
  5. Can anyone give me the part number for a new choke cable assembly for a '71? I can't locate it in any of the part diagrams.
  6. The choke cable that attaches to the front carburetor is not returning to where it should after the choke is pulled back and pushed forward again. I tried lubricating all of the joints that the cable triggers on the front carburetor, but it still isn't fully returning to normal; this causes the car to idle higher than it should and will flood the car when it's turned off(unless I open up the hood and push the lever back to normal). Anyone know how I can fix this issue?
  7. Does anyone have the Nissan part number for the choke knob? I can't find it in any of the part diagrams.
  8. I have an uncracked 240z dashboard sitting in my garage that has small specks of overspray on it in some places. I used armor all on it today and some black started coming off onto the rag. Has anyone else experienced that? What is the best cleaning agent that will remove overspray without damaging the dash?
  9. Anyone have any recommendations?
  10. What brand of adhesive/sealant would you guys recommend for reattaching the lenses to the bodies? Also, do the rubber pads that were between the lens and the body have to be there when the lights are sealed back together? because the rubber pieces on mine were wasted so I threw them out. I'm assuming a thick blob of some type of adhesive/sealant can replace those couple rubber pieces.
  11. Esprist's method worked perfectly. I think mine were tougher to get off than yours because there was some sort of adhesive glue holding it on. Esprist, what did you use to replace the original gasket (sealant maybe) that secured the lens to the body?
  12. lm71z replied to KenshinX's topic in Interior
    I posted a thread a while back ago describing this same exact problem. Loosen the screws around the mechanism and then try to turn in back in the right direction. That worked for me and I had the same exact problem as you. Let me know if that works.
  13. I have a pair of 240z tail lights that are in amazing condition, but they are extremely filthy and covered in masking tape residue. I need to separate the lens from the body without breaking anything. Can someone explain to me how to do this? I read in one thread that the lens and body will seperate if you submerge them in hot water; has anyone else tried this method? Also, does anyone know how I can remove the old tape residue from the lenses without damaging the plastic? The best way I can think of is using duct tape.
  14. I need advice on how to spray the wheel with the semi-gloss urethane. How did you guys do it? Did you hang it up somewhere when you sprayed it? When you talk about applying multiple layers of lacquer, do you just wait a few minutes in between each coat or do you have to wait 24 hours before you can apply another coat?
  15. Okay, here's my 240z's steering wheel with the spokes freshly painted and the rim sanded. I sanded the rim for hours and this is as light as the wheel will come. I washed and scrubbed it 2 times with murphy's oil soap. I'm planning on applying one or two coats of minwax antique maple stain(same color as cherrywood just a little more reddish). What do you guys think? Will the lighter color stain accentuate the color of the steering wheel? or will it not blend in correctly?
  16. Are these still available from Nissan? I found the most current part number in the Nissan FAST system but it's not available. I'm probably going to buy one for $550 from new-datsun-parts.com. Is that a fair price for a brand new 240z bumper?
  17. I sanded the crap out of it, but the wheel still has the original color in it. Does that matter? I'm hoping the stain will blend with the old color and not stand apart from it.
  18. I cleaned the wood/plastic rim of the steering wheel with Murphy's Oil Soap and an SOS soap pad. The rim is now very dry and dull looking, but some of the original finish is still there in spots. For those people who have refinished their steering wheel, did you make sure to completely remove the old finish before staining it? I noticed that some people just cleaned the wheel and applied lacquer without staining it. If I were to do that, wouldn't the color of the wheel remain the same after lacquer is applied?
  19. I've read some instructions on how to adjust the hinges on a 240z's hood to get it to line up properly, but all of the instructions I read were very unclear. The hood on my 240z is off center; when the hood is closed, there's barely any space between the driver's side fender and the hood and plenty of space on the passenger's side. Also, the hood is not sitting flush with the headlight bucket on the driver's side(it's slightly elevated above the headlight bucket). Does anyone have any labeled photos or detailed instructions on which bolts/nuts i need to turn to get the hood aligned properly?
  20. Does anyone know if the early 240z's are supposed to have this seal or not?
  21. Actually, I can't find any of the firewall grommets in the Nissan FAST system. Would anyone happen to know what category they are under?
  22. Does anyone have the Nissan part numbers for the carb/choke cable grommet and the wiring grommet? I'm pretty sure MSA has neither of those. I haven't been able to find any of the grommets in the Nissan diagrams except for the heater hose ones.
  23. I already have the heater hose grommets for my 240z, but I can't seem to find the other grommets that are located at other places on the firewall. I believe there are 2 more grommets besides the heater hose ones. One is for the choke cables and the other is for electrical wires. Does anyone have the Nissan part numbers for these grommets?
  24. Are the latch mechanisms part of the door lock assemblies that MSA sells?
  25. Does anyone know if new door latch mechanisms are available anywhere? I'm referring to the mechanism that slams into the door striker and secures the door shut. The ones on my 240z seem to be pretty beat up and are not functioning smoothly.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.