Jump to content
mikec(nz)

240k Race car - GTR tribute

Recommended Posts

Cheers Flauski, yeah I remember that. Great you have another car.

Well a few delays as my order from the Z store got nicely sent to Malta rather than NZ. Close, not!

In the meantime got the sump modified, cross member modified and new drive pulley.

Heres some pics

 

IMG_20191220_1423276.jpg

IMG_20191216_1728455.jpg

IMG_20191220_1426017.jpg

IMG_20191220_1423215.jpg

IMG_20191216_1728426.jpg

IMG_20191217_1746336.jpg

IMG_20191220_1421492.jpg

IMG_20191220_1422214.jpg

IMG_20191220_1422320.jpg

IMG_20191220_1421547.jpg

IMG_20191220_1421571.jpg

IMG_20191216_1726487.jpg

IMG_20191216_1726541.jpg

Edited by mikec(nz)
  • Like 2

Share this post


Link to post
Share on other sites

More progress, finally the last parts arrive after being redirected from Malta. Thanks Fedex.

Tested the sump oil levels (5l) modified so the old skool GTR sump could clear the exhaust and the sump/gearbox bracket would clear the extractors.

Mocked up the manifolds and read to go into the newly cleaned engine bay.

 

IMG_20191228_1757019.jpg

IMG_20191228_1757089.jpg

IMG_20191228_1756570.jpg

IMG_20191228_1757174.jpg

IMG_20191228_1757244.jpg

Share this post


Link to post
Share on other sites

Still a few parts to fit, the new OS Giken twin plate clutch and we had to get the right oil pump spindle. Turns out the Kamarei one only works with their special oil pump. 

More pics soon.

IMG_20191222_1519190.jpg

IMG_20191227_1623305.jpg

IMG_20191227_1623192.jpg

IMG_20191227_1623336.jpg

IMG_20191227_1623551.jpg

  • Like 2

Share this post


Link to post
Share on other sites

Engine in and clutch done, link from sump to gearbox fitted and manifolds and carbs fitted.

New engine mounts. Note you need specific 240k ones, hard to find and very expensive compared to 240Z.

That sump which is actually for a Hakosuka, requires cross member modification, slight block grinding and exhaust manifold modification.

Will also need a new sway bar, so its not a direct bolt up for a 240k.

Getting closer, might be ready for start up in a few days.

 

IMG_20191230_1725191.jpg

IMG_20191230_1725335.jpg

IMG_20191230_1725382.jpg

IMG_20191230_1232198.jpg

IMG_20191230_1231436.jpg

Edited by mikec(nz)
Stupid speelcheck
  • Like 2

Share this post


Link to post
Share on other sites

Sorry leadfoot is painful, all day for Just a few minutes of racing. No run off areas and a fun stone bridge if you make a mistake, happy to spectate at that event.  Was going to try to get it ready for the festival at taupo in Mid Jan but not going to make it. Will be at the GTR festival.

More progress today

New plugs, new oil cooler arrived and rest of carbs fitted. Belts fitted etc

 

IMG_20191231_1246412.jpg

IMG_20191231_1425458.jpg

IMG_20191231_1246480.jpg

IMG_20191231_1246527.jpg

  • Like 1

Share this post


Link to post
Share on other sites

Well good news, the engine started today with no real dramas (just a faulty electric fan relay).  Running a bit lean and my engine builder was a bit concerned with the whine from the twin idler set up.  But according to Dr Google thats normal and all seems happy.  Off to the dyno in a few weeks and will report back then..

In the meantime heres a couple of videos

Video engine starting today https://youtu.be/8HT150MspWo

 

 

Few good revs https://youtu.be/EpZ9BPRo5xk

 

Cheers  Mike

  • Like 3

Share this post


Link to post
Share on other sites

Dyno day today. Car went well. Interesting results which I will post later. Heres teaser pics

I'll get a video up to youtube soon.

As we dropped a bit of capacity you would think we would get less power but got roughly the same as before 250 rwhp, but lots more torque.  But it is running richer so will sort that out after we have given it a proper run in at a track day and then see what happens.

Otherwise is running fine, temps steady and no knock or noise, rock solid fuel pressure.

Admit I did hope for more power straight off the bat, but will see what develops. Every run made a few HP more so next is a good run in and then some tuning.

IMG_20200229_0938524.jpg

IMG_20200229_0956549.jpg

Edited by mikec(nz)
Spelling

Share this post


Link to post
Share on other sites

Brilliant!

 

I was lucky enough to meet some guys over here at the phillip island historics last month who made the trip from NZ who were big fans of yours!

  • Thanks 1

Share this post


Link to post
Share on other sites
Posted (edited)

Thanks Mastadd240k, they mention they had run into some 240k owners.

Now lockdown was over managed to get it to the track to run in the engine.  What better day than the Prowear 2020 GTR Festival.

Did not taken any real photos, but Glenn from the Lab did a video of the event, some footage in that

https://www.youtube.com/watch?v=3-xtPZUrC1U 

Back to Coastline Automotive for an oil change then back to the dyno for another check, then we can decide whether to spend some more time tuning.

Dyno charts from Feb 20 showing new engine vs old engine.  That old engine really ran well for its age.  It did have slightly bigger capacity and extensive head work.  Surprised the new one was not much different.

The old engine lines on the chart is very hard to see.

AFR Feb 20.pdf HP-Torque Feb 20.pdf

Edited by mikec(nz)
Extra info
  • Like 1

Share this post


Link to post
Share on other sites

Some pics of the GTR Festival - not really a race event but great opportunity to run the engine in.  The video is above but her is some pics of the K from the event.  Thanks to Maria Panova Photography http://www.mariapanova.com/

104151726_1408090756045520_7679434006689599528_o.jpg104130812_1408088096045786_4112621056468500307_o.jpg104108475_1408088792712383_3783776327423169936_o.jpg104075753_1408090439378885_558294290389584868_o.jpg103934154_1408089449378984_3282432635154599344_o.jpg103838417_1408091699378759_8635405197713750490_o.jpg103834250_1408091506045445_7708490575722208573_o.jpg103650177_1408091156045480_5002291626034083225_o.jpg83719101_1408092036045392_5824536845799334757_o.jpg104941671_1408090646045531_4167770981183923300_o.jpg104496831_1408088819379047_5971919001594413619_o.jpg104419986_1408091879378741_8666679183767520868_o.jpg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.