Jump to content
Remove Ads
  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type

Categories

There are no results to display.

Forums

  • COMMUNITY FORUMS
    • Social Club
    • Regional Talk
    • Convention & Events
    • General Tech Talk
  • CAR TECH FORUMS
    • Classic Z - 1st Generation
    • Classic ZX - 2nd to 4th Generation
    • Modern Z - 5th to 7th Generation
    • JDM - Japanese Domestic Market
    • Other Datsun Models
    • Racing
    • GENRE SPECIFIC
  • MARKETPLACE FORUMS
    • CLASSIFIEDS
    • GARAGE BUSINESS

Calendars

  • Zcar Events and Shows
  • Zcar Club Washington
  • Classic Car Shows

Categories

  • Wiring Diagrams
  • Microfiche
  • Service Documents
  • Brochures
  • Factory Service Manuals
    • 240z
    • 260z
    • 280z
    • 280zx
    • 300zx
  • Manuals
    • Owner Manuals
  • Website Support
  • CAD Files
  • Software Tools
  • Tech Articles
  • Club Graphics

Product Groups

  • Club Merchandise
  • Direct Advertising
  • Legacy Products

Blogs

  • Blog Z4Her
  • Blog Scarab#157
  • Blog Michael's Zcar
  • Blog fawazalazmi
  • Blog BigBird
  • Blog jamul scott
  • Blog blindsquad
  • Blog BlueSky224
  • Blog Ardent
  • Guy Mayer
  • Blog scruz32
  • Blog ryanonthevedder
  • Blog EuroDat
  • Blog vuddysr
  • Blog 77_FairladyZ
  • Blog DanielE
  • Blog illest240z
  • adidas nmd r1 rose
  • Blogs 2 Forums
  • Community News
  • docfedt
  • Yarb's Blog2
  • Yarb's Blog1
  • Dexter
  • Aaron McClanahan
  • adidas pas cher
  • Blog fastmike
  • Affortable Sandblast set up
  • Saint Philip's Day
  • rickster240z
  • CaseyByrd72 Restoration
  • noradress.com
  • Blaxdragon's Blog
  • Tracy Westman
  • Blog zman2003
  • Blog juniorzep
  • Blog Mikes Z car
  • Blog pukegreenz
  • Blog ConchZ
  • Blog hls55@yahoo.com
  • Blog stevef1972z
  • Blog mel marabante
  • Blog zcarlady1
  • Blog miker
  • Blog Rainman
  • Blog 59blane
  • Blog Montezuma
  • Blog titaniumspine
  • Blog smokingwheels
  • Blog sleepyzzz
  • 1975 280Z Project
  • Blog mikeddiezel
  • Blog momluvdherz
  • Blog mattm180
  • Blog tamo3
  • Blog david gordon
  • Blog cycloid
  • Blog Ken M1
  • Blog Billmadson
  • Blog John78Z
  • Mike's Blog
  • Blog House3571
  • Blog G2Services
  • Blog ThomasD.
  • Blog mkwhite
  • Blog TheNateums
  • Blog Gary in NJ
  • Blog zorroo24

Find results in

Find results that contain...

Date Created

  • Start

    End

Last Updated

  • Start

    End


Filter by number of...

Found 1 result

  1. I will be restoring my 72z back to "near original" condition. I will utilize all original equipment that can be reused and replace what can't with new. I am not overly concerned with originality, especially if it is expensive. I have set a budget of $7,700, and must include some tools, but I will document that as I go. I will be utilizing two primary resources as guides for the process; How to Restore Your Datsun Z-Car by Wick Humble and of course, the Haynes manual. I began last weekend by disconnecting all wiring and hoses from the engine and transmission and, preparing for removal. Two of the rear drive shaft bolts did not want to break loose so I persuaded them with the sawzall. I used my floor jack to support and remove the transmission without much trouble. I used a 2 ton engine hoist to remove the engine with a 10 foot section of chain wrapped around the exhaust header and an M10 bolt inserted into the bracket hole(?) next to the fuel pump. I purchased a 750lb capacity engine stand from Harbor Freight for $46. You can see it in photo 108 attached. I had to purchase the mounting bolts ($9) which were M12x1.5, 75 mm long. Unfortunately they were too long for the stand and bottomed out in the engine block before tightening so I cut a little off. In all, It took me about 10 hours to get the engine and trans out. Today I worked for about 5 hours removing the battery doors, front bumper, grill, hood hinges, windshield cleaner reservoir, coil, and started brake lines. The brake lines have been a pain! I went to the auto parts store and got flared tube wrench for $6. Well worth the money, but I still couldn't get one loose. It's in the proportioning valve so...... Thanks for reading. Feel free to post questions, comments, and suggestions.
Remove Ads

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.