Jump to content

madkaw

Members
  • Content Count

    4,063
  • Joined

  • Last visited

  • Days Won

    13

Everything posted by madkaw

  1. If your talking to me , you maybe be off a drive tooth from the oil pump gear . Have you removed the oil pump at all? Has it always been this far off. Is the tang at 11:25 o’clock at TDC ? Have you had the engine apart or oil pump out ? Is the rotor pointing at #1 spark plug at TDC - possibly the wires are one hole off
  2. Well I like the way they ride . I’m running about a 1/4 turn out for all these wonderful roads around here . The ride is decent and can be made softer than my non- adjustable KYB’s - but just a smidge . I take a long drive tomorrow so I will really give them some miles . Nice curvy Indiana roads . I’m taking my friend gearhead with me for the ride . Actually I’ll have two passengers l but cranky arse has to stay in the back .
  3. I think low 4 is possible if I can hook up or burn up my clutch - lol. I need to do a quarter mile , the GPS can time that too!
  4. What’s your max ignition timing 100kpa
  5. Well I can’t keep up with what I post anymore . The 3.2 is now running with the MN47 head again . Since the last post I had put miles on the p90 while I was fixing a 71 for a customer . Meanwhile the MN head got new Manely valves and bronze guides . I swapped it back I’m with the proper head gasket thickness and should be back to 10.5:1 . Cylinder pressure is around 220 with compression tester . Pistons were pretty much broke in , so just a tune and start flogging . I managed a quick 0-60 time of 4.77 seconds . This is a beast motor . It’s amazing how hard it pulls even in 4h gear . Dyno appointment is in November - everyone is booked up until then . 8B4867CC-29D6-428F-A1D7-5F72482973E3.MP4
  6. Sounds like a winner . I think I saw it in the video. Cross flow head ?
  7. What won the people’s choice ?
  8. Well darn , too far for me . I blew my chance when it was close .
  9. I had concerns of this when I was thinking of going . I guess if I had made it I would have been one of the few in the pics that had a mask on . I guess it wasn’t cool ? I figured with older cars you would have older people , so more masks ?
  10. Joesph, I will PM you about who I spoke to. Yes my measurement was 6mm. Looking at the pic you provided is not representative of a properly torqued nut . If it is the same as what I was provided them the diagram is showing a nut with 1 thread engaged. My nut Has only 4.5 threads . To get to 4mm after torquing , there would only be about 2 threads at most showing .
  11. I mean - KYB thought it thru . They have a small standoff at the bottom. You give up a bit of shock length , but they fit . I have a pair of old red Koni’s that came out of a 70, I’ll pair them up and see how they compare . Those shocks the gland nut and shock were one piece insert . Im going to cut down the gland nut a bit more because I don’t see MSA or Koni doing anything more . I’m hoping if I do anything I will give someone else heads up of the possible headache
  12. I guess I don’t understand your logic . Variance in parts is why you provide a cushion . Also, these shocks were designed to drop in a tube so they need to fit the tube- regardless if it was designed for oil 50 years ago . These shocks were designed or engineered in the last year - at most ? Yes it’s a 9/71 .
  13. The KONI nut is a thick walled nut . Even after increasing the ID , it still has close to 1/8” wall thickness . It just needed to be cut deeper and it would have been fine . Better yet - the KONIs should have been made -like most shocks for this car- with a smaller ID at the bottom to keep off the weld bead at the bottom
  14. So disappointed that the modified gland nuts do not get the job done . Even modified I only have 1-1/2 turns on the gland nut . Still showing 6mm of nut . They only machined off 2mm when they should have done 4. Called MSA - and it’s basically my problem . It’s my fault that the strut tube has a factory weld bead at the bottom . I could somehow grind the weld down at the bottom of the tube - yeah . So these modified glands are not a guarantee that these will fit your early Z . My car being a 9/71 isn’t that early - but early enough I guess . Now I get to pay a machinist to modify the modified gland nuts that are supposed to fit my year car - woohoo. Not much sympathy from MSA , they just sell the shocks .
  15. The steel bushing orientation was not discussed earlier in this thread , that’s why I posted the question . AK260 showed what he did for orientation , which seemed to make sense , but now you show the bushing flipped the other way . It would seem to me that AK260 has it correct to extend travel of the bump stop . It would be nice to get some clarity from KONI .
  16. KYB’s . It looks like a hefty weld bead on the bottom of the strut assembly . The KONI is wider at the bottom of the cartridge, and I believe the cartridge is hitting the weld bead . KYB’s also have that small pedestal on the bottom of its . The cartridge should have been shorter . The last red Koni’s I took out of my 70 had the gland nut integral with the cartridge .
  17. MSA is sending me different gland nuts - probably as in the previous post - chamfered so they will fit .
  18. Looks like I’m in the same boat with the fronts too tall for the gland nuts - 9/71 Almost didn’t get one out too! Well I didn’t have much hope for Zcon - but all hope is gone . Not enough time in the day
  19. That’s what I thought -but wanted to make sure
  20. Steel bushing guys - on top of strut piston ! Is that on correctly ? What is it’s purpose? My KYB’s do not have this . Anyone ?
  21. I was referring to the steel bushing . My KYB’s didn’t have this . I don’t see it in the instructions
  22. Freaking IKEA instructions - give me a break . what about the spacer ? I can’t find it in the instructions .
  23. I would have been besides myself -pissed if I had to do that with a brand new set up (lock nut) . I will take your advise seriously . I wonder if my old KYB nylon lock nuts will work? I hope you do give them some feedback . That shouldn’t have been overlooked . Makes me wonder if they actually have a test vehicle to mock this stuff up on . I’d be happy with a T handle that fit the slot . Since there is two full turns of adjustment , having marks on a dial is kind of worthless. Kind of like a carb mixture screw - can’t remember how many turns out , so you dial it in while counting and dial it back out .
  24. You say it wouldn’t get deep enough ? To fit under the strut tower cap ?
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.