GILDIA

Hi in the picture there is a green cable with a label on it, does this green cable goes to a white cable?

The W wire comes from the starter and it goes to a fusible link and then to the Ammeter and in to the fuse box, and the WR wire comes from the Alternator, I think you should check the fusible links, this diagram might help, there are good electrical people here that might give you better help, they had help me with a lot of issues (because i am rewiring my Z from scratch) So good luck...

regarding the question about the VR no it is not the VR, it is the ACC's relay, The Voltage regulator is located in the right fender.

The clock, dash lights and step light are wire togheter trough a RL (Red/Blue) wire, (it changes its colos for diferent instruments, clock for example changes to blue), and it goes to the fuse box, perhaps you should check continuity and verify that you are getting voltaje on this wire before you unplug anything.

Thank you, it will help me a lot i also was looking for the speedo cable and this picture cover both of them, thanks again

Hi, I am tring to wire the reverse light , In the diagram there is a reverse switch, does any body know where is this switch located? I think it should be near te trassmision but i am not quite sure Thank you all

You could try switching back to points, if she still doesn't starts then the problem is not the pertronix, it could be the distributor cap

Thanks E, well i think I am ready to put the new wires for the hazard siwtch, the turn signal, and the stop, I'll let you know what happens, By the way the Headlight are working but I can get the Hi beam to work, any advice Thanks

Thanks E, I just found the relay, it is under the dash and behind the seteering column, Since I am re-wiring from scratch, Can I move the location of this flasher to the passenger side so i Can have all th relays togheter in one location? Thanks E, as always your info is of great help.

This is the diagram I have for the T/S switch, as you can see it seems like if the switch is out of the combo switch, so I was wondering if this could be a Flasher, i read in one of your post that this cars used 2 flashers, one for the T/S and one for the Hazard

Thanks E, Actually the first picture is the picture of my combo switch, i could figure the headlights (but i still don't have the hi beam), but these white and green wires from the diagram I can't figure them out, I don't know where to connect them, I dont see any white nor green wire comming from the combo switch, perhaps you can tell me where to connect them, Thanks for the help

HI to all, i am re-wiring the Z (72) but I can not find a T/S flash SW, does anyone know where is this switch located ? i Think it could be under the dash but not sure where, in the diagram it appears with a white and a green wire attached to it and the green wire goes to the hazard switch and the white wire goes to the combo switch Thank you

Hi, does any one know if the speedometer has a prong? Thank you

Sorry Dave, I haven't wire that part yet, as soon as I'll do it I will let you know

Hi, Dave I Paid $63 USD for the pair, I am still in the process of wiring the car, and so far the Headlights work, so I think it maight be a 72 Hope it helps

:stupid:I guess i am going to need a new gauge, I tested it with an external source (12 volt) and the gauge skoke start ti get out of the gauge :stupid: So I made a mistake but i learned from it ...

I just measure at the VR and i get 13.9 Volts to the gauge, and i also measure the resistance from the temp sensor and i get around 200 ohms and it decreases at time pases by, but i dont get a reading at the gauge, I am going to open it and clean it

I just ground the but i am not getting any lecture from it, do you know what is the voltaje I should get from the VR...

So, if i ground the sensor wire, i should read maximum?

Thanks E, regarding the power it feeds through the VR, and it just goes directly to the oil and temp sensors.

I got this switch from ebay, it is supposed to be a 72, but I am not sure, anyhow here are the pictures of it.

Thank you guys, I will try it, what if when i ground them they wont read? does that mean that I will need a new gauge?

Hi, does any body knows how to test the OIL/TEMP gauge, i can't get a single lecture from them. Thank you

Hi, looking at the picture, where does the terminal (circle in red) connects to? I am having problems figuring it out Thank you

The blue one comes from the fuse bix and what does it connects?