Jump to content
Remove Ads
  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type

Categories

There are no results to display.

Forums

  • COMMUNITY FORUMS
    • Social Club
    • Regional Talk
    • Convention & Events
    • General Tech Talk
  • CAR TECH FORUMS
    • Classic Z - 1st Generation
    • Classic ZX - 2nd to 4th Generation
    • Modern Z - 5th to 7th Generation
    • JDM - Japanese Domestic Market
    • Other Datsun Models
    • Racing
    • GENRE SPECIFIC
  • MARKETPLACE FORUMS
    • CLASSIFIEDS
    • GARAGE BUSINESS

Calendars

  • Zcar Events and Shows
  • Zcar Club Washington
  • Classic Car Shows

Categories

  • Wiring Diagrams
  • Microfiche
  • Service Documents
  • Brochures
  • Factory Service Manuals
    • 240z
    • 260z
    • 280z
    • 280zx
    • 300zx
  • Manuals
    • Owner Manuals
  • Website Support
  • CAD Files
  • Software Tools
  • Tech Articles
  • Club Graphics

Product Groups

  • Club Merchandise
  • Direct Advertising
  • Legacy Products

Blogs

  • Blog Z4Her
  • Blog Scarab#157
  • Blog Michael's Zcar
  • Blog fawazalazmi
  • Blog BigBird
  • Blog jamul scott
  • Blog blindsquad
  • Blog BlueSky224
  • Blog Ardent
  • Guy Mayer
  • Blog scruz32
  • Blog ryanonthevedder
  • Blog EuroDat
  • Blog vuddysr
  • Blog 77_FairladyZ
  • Blog DanielE
  • Blog illest240z
  • adidas nmd r1 rose
  • Blogs 2 Forums
  • Community News
  • docfedt
  • Yarb's Blog2
  • Yarb's Blog1
  • Dexter
  • Aaron McClanahan
  • adidas pas cher
  • Blog fastmike
  • Affortable Sandblast set up
  • Saint Philip's Day
  • rickster240z
  • CaseyByrd72 Restoration
  • noradress.com
  • Blaxdragon's Blog
  • Tracy Westman
  • Blog zman2003
  • Blog juniorzep
  • Blog Mikes Z car
  • Blog pukegreenz
  • Blog ConchZ
  • Blog hls55@yahoo.com
  • Blog stevef1972z
  • Blog mel marabante
  • Blog zcarlady1
  • Blog miker
  • Blog Rainman
  • Blog 59blane
  • Blog Montezuma
  • Blog titaniumspine
  • Blog smokingwheels
  • Blog sleepyzzz
  • 1975 280Z Project
  • Blog mikeddiezel
  • Blog momluvdherz
  • Blog mattm180
  • Blog tamo3
  • Blog david gordon
  • Blog cycloid
  • Blog Ken M1
  • Blog Billmadson
  • Blog John78Z
  • Mike's Blog
  • Blog House3571
  • Blog G2Services
  • Blog ThomasD.
  • Blog mkwhite
  • Blog TheNateums
  • Blog Gary in NJ
  • Blog zorroo24

Find results in

Find results that contain...

Date Created

  • Start

    End

Last Updated

  • Start

    End


Filter by number of...

Found 1 result

  1. Hey Everybody, A few months ago I acquired myself a rust bucket 76' 280z (mainly for parts and drivetrain) I want to get the engine running to confirm that it is worthy of holding onto. Somehow I cannot get the injectors to pulse. The car fires right up when hit with ether and will run as long as ether is supplied. BEFORE everyone goes ahead and says it I DO have the EFI BIBLE and have gone through it best of my ability to follow the testing suggestions. What I've done so far: Pulled all 6 injectors, tested that they open and produce fuel, not clogged. Have a NEW Fuel pump hooked right up to the fuel line. Connected back at the tank so that the pump activates when cranking. Checked all four fusible links on passenger side of car with volt meter. All seem good. Ran a Negative jumper from coil to pin 1 in the ecu. To eliminate bad ground wiring in harness. Checked pin 10, 20 for fuel pump circuit and relay. Injectors have a current, they are lacking their ground from the ecu when I crank. Did a pulse test ( ran a negative to the - terminal of coil, with key On grounded it on the body quickly to check for pulse) got all six injectors to pulse a few times. They only pulsed a couple times and then this didnt work anymore.) From here I'm not sure what else to do. I read that maybe I should check out the dropping resistors? How would I test these? Also how would I test the EFI Relay? Thanks in advance
Remove Ads

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.