nix240z

I believe I could reproduce this item, if there is enough interest in it. Steve

I know.. you beat me out at $415, I went $410.. I just picked up a NOS set on ebay last night for $200 plus shipping..

now it looks like sets are going more in the $599.99 range now with free shipping...

Speedometer cable grommet on firewall. Will need to be cut and glued back together, I machined so it has some meat in the center for easy gluing, plus hole in firewall will help hold it together. No other way around this, since ends of speedo cable are large and will not come off. I will list on website when ready for purchase. 240zrubberparts.com

Antenna Drain tube grommet, located left rear wheel well area.

yes...

Fuel sending/fuel pump wiring harness grommet, located in the right rear hatch area.

I have a complete set of Blemish (Blems) insulators with small imperfections for sale at $75 shipped. The imperfections will really not be seen once installed on the car. If anyone is interested send me a PM. I figured I would try them here first, before I put them up on the website for sale. Steve Datsun 240z rubber parts

Marty , the plugs are on the underside of the rocker panels, two on each side front and rear. You will have to get on the ground and look up to see the holes. Steve

Chas Thanks for the kind words on site, yes I have the same thing on my Ipad in the gallery, but it works fine on my computer. Steve

I now have my website up and am working on it, as it is still under construction. Datsun 240z rubber parts I will also keep this thread updated with new products. thanks for all the support and all that have ordered parts from me. Steve

The Correct style for 70-71 choke knob...

In less than a week we have the door lock mechanism small rubber reproductions. Getting the main tumbler installed is a tight fit but it was done. There have been threads about these rubber pieces missing and making the doors not close correctly. 90% of the time these pieces are missing or damaged on the door lock mechanism.

Was like Santa came yesterday....

Machined up a early type original speedo cable grommet, just have to clean it up a little with some fine sanding. The previous picture I posted, of the speedo grommet is from a new Nissan cable that I purchased back in the early 90's. I machined it with some meat in the center so it can be cut and then glued back in place. I Dont think it will stretch over the ends of the cable but I will try and do it. The good thing about this grommet is that it will also be machined into the Radio antenna drain tube grommet in the left rear wheel well area. should be done in about a week.

Price list of items for sale. Pm me with any questions. Complete brake and fuel line insulator set $150 Steering Rack Tank (note: nostalgia look only) $15 rear bumper to fender shims $11each front bumper to fender shims $11 each headlight wire seal $8 each upper quarter window seal $15 set hatch stopper bumpers $5 each brake booster insulator Black $10 each brake booster insulator RED $15 each rear brake drum plugs $8 each rocker panel plugs $5 each wiper motor firewall seal $15 lower window inside door bumper with clip $10 each rear hatch lock seal $8 70-71 gas door latch seal $8 70-72 main wiring harness $30 72-73 choke cable grommet on firewall $25 70-71 choke cable grommet on firewall straight original $25 hood release grommet on fire wall $10 70 series 1 early hood bumper $15ea 70-73 clutch stopper bumper $20 wiper motor bracket insulators set $30 radiator wire pass through insulators set $15 70-71 choke plate blank tape reproduction $10 Series 1 hood less maplight Bezel reproduction $35

replace your cracked, missing or worn out radiator wire pass thru insulators. Two sizes per set, one for the small round hole and the other lager hole as pictured. right side is the original and left side is reproduction.

Reproduction Series 1 Map Light Bezel...

replace that missing, cracked, worn out rightside choke plate blank. This is reproduced in urethane rubber, that should last many years. Cut to fit..... plate is not included.

Ok, seems there are two types or maybe 3. The 69-70 Series 1 which is a hood release and speedo pass through grommet and then all others are just a speedo grommet, maybe in two types. If you have something different let me know. Here is a pic of the sample I have and could reproduce. Steve

Replace your worn out, dry rotted wiper motor mounting bracket insulators. Each insulator has the correct notch for the bracket. Metal insert not included rubber only.

A Prototype of the 72-73 Radio faceplate reproduction. prototype on top and original below.

wiper linkage boot is on my list for sure... Steve

Replace that missing or worn out clutch pedal stopper with a new reproduction....

Now available are the Early 70 series 1 hood bumpers...