joe newsom

My 240z project

    Recommended Posts


    Had a great weekend working on the zcar

    Got the front suspension torn apart and media blasted and coated with POR 15 / minus the steering rack. Will have todo some more research on how to move forward on that.

    All nuts and bolts zinc plated along with some other goodies.

    Transmission cleaned / polished and sprayed with caliper paint. It was getting dark so pic didn’t turn out that well.IMG_4407.JPGIMG_4408.JPGIMG_4386.JPG

    Dialed in my garage too haha

    IMG_4446.JPGIMG_4445.JPGIMG_4423.JPG


    Sent from my iPhone using Classic Zcar Club mobile

    • Like 1

    Share this post


    Link to post
    Share on other sites

     

    3 hours ago, grannyknot said:

    Joe,  your plating looks terrific, care to reveal your method, procedures or secrets?

    Agree with Grannyknot and Patcon.  Maybe it's that clean northwest coastal air.

    Can I send you a box of my parts that still need plating? :P

    Share this post


    Link to post
    Share on other sites

    Started out by picking motormans brain, he turned me on to Caswell. After a week of bugging their tech and scouring the internet I got the basics understanding. I think the using caswell’s calculator really helped. However I do think the most valuable thing that I really noticed a difference is putting the brightener in each time at the beginning. About a teaspoon.

     

     

    Sent from my iPhone using Classic Zcar Club mobile

     

    Share this post


    Link to post
    Share on other sites

    6 hours ago, joe newsom said:

    started out by picking motorman brain, he turned me on to Caswell. After a week of bugging their tech and scouring the internet I got the basics understanding. I think the using caswell’s calculator really helped. However I do think the most valuable thing that I really noticed a difference is putting the brightener in each time at the beginning. About a teaspoon.


    Sent from my iPhone using Classic Zcar Club mobile

    What are you using for power supply? What are your plating times? Dip times? Are you using Blue Chromate? You could always post up your experience and methods in my Caswell thread for posterities sake

    • Like 2

    Share this post


    Link to post
    Share on other sites

    Patcon I will post up some pics and process on that thread if I can find it. I have found on my phone the app is abit difficult to look up threads.

     

    Here is power supply

     

    Dr.meter

    4.2 out of 5 stars 189 Reviews

    Dr.meter 30V/5A Single-Output DC Power Supply 110V/220V Switchable with Alligator Clip included, US 3-prong Cable,PS305DM

     

    I thread all polished hardware on to 18g brass wire. I found that other materials are unpredictable and left pieces in the same soak dull

     

    Then dip in muriatic acid 50/50 distilled water until it quits fizzing.

    Rinsed in distilled bucket

     

    Let hang into degreaser at 120 degrees until ready usually about 15 min.

    Rinsed in distilled bucket

     

    Load into zinc tank. Which is constantly heated to 75 degrees with one of submersible heater for fish tank. Loads were calculated to run at 5 amps the max my rectifier will do, for 15 min.

    Trying to remember to rotate in middle of load became challenge.

    Rinsed in distilled bucket

    Dipped into Blue Chromate for about 5-10 seconds

    Rinsed in distilled bucket

    Dipped into Yellow Chromate for about 15 seconds

    Rinsed in distilled bucket

     

    Yellow chromate I mixed myself using 10 oz of sodium dichromate which I bought cheaply on eBay and 1 oz sulfuric acid ( battery acid) to one gallon of distilled water.

    All other products were bought at Caswell

     

    Hope this helps. I really noticed the difference in the properties of the zinc by adding brightener at the beginning of each day I was going to zinc. Noticeably different outcome when I didn’t add it in the beginning of my day.

     

     

     

     

     

    Sent from my iPhone using Classic Zcar Club mobile

     

     

    Share this post


    Link to post
    Share on other sites

    This is the thread. I will copy and paste from your last post. Add what you like...

    • Like 1

    Share this post


    Link to post
    Share on other sites

    No more plating pictures, please, until you show pictures of your set-up and explain your process in detail..  Hurting my self-esteem.:(

    Share this post


    Link to post
    Share on other sites

    BTW, 'I do this all the time', and, 'I don't understand why it's such a big deal' are not acceptable responses.

    • Like 1

    Share this post


    Link to post
    Share on other sites
    BTW, 'I do this all the time', and, 'I don't understand why it's such a big deal' are not acceptable responses.

    Namerow I thought I explained. I will be away from the zcar this weekend. I have husband duties. When I get back I will take some photos and write up detailed as I can. I did some black chomate on the seatbelt bolts and they came out kind of cool. I will post some of those too. I should trade you for pics under your dash default_laugh.png. I didn’t take enough and have a couple mystery wires.

     

     

    Sent from my iPhone using Classic Zcar Club mobile

    Share this post


    Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now