Old Want Ads
Old ads for wanted items.
880 topics in this forum
-
- 4 replies
- 1k views
Need a set of lightweight four studs, not heavy Performance brand thanks. Preferably 8" but will consider 7 or 71/2".
Last reply by 260DET, -
-
- 10 replies
- 1.4k views
I am looking for a '70-'71 Datsun 240Z. Minimum requirements are: -minimal to no rust -all or nearly all parts accounted for and included -running or require minimal effort/expense to get running -interior should be in fair condition Ideal candidate will have also have the following: -ENGINE: an '81-'83 L28 non-turbo motor (this will have flat top pistons) which will be an F54 -HEAD: an '81-'82 P90 head (Does this head have brass rings?) -CARB: round top SU carbs -TRANNY: a '77-'79 5-speed -REAREND: a R180 3.9 from a non-turbo car Acceptable cars will meet at least the minimum requirements and may have some of the additional features listed under the ideal candidate. …
Last reply by texasz, -
- 0 replies
- 878 views
need it, and I need it fast. willing to pay for express shipping. MSA asking too much (I think, anyway....$75-ish) shipped to ZIP 29550 email me at wesd@post.com if you can help me out thanks!! *EDIT* this request has been filled. thanks to everyone for their offers.
Last reply by shyfty, -
- 15 replies
- 1.3k views
I need the inside of the glovebox for my 240Z, I have a VERY early '71. If other year models work that's fine, but I need the actual 'box' of the glovebox. This seems to be some type of paper/cardboard material and mine is trashed. Used and cheap is good as long as it is intact, new is ok too but I have not found anywhere that has them. ANY HELP WOULD BE GREAT!!
Last reply by texasz, -
- 1 reply
- 820 views
I'am just after a few small bits..... The top 2 L pieces of chrome from the rear window- the bits on the top on each side. A new rear window seal.(unfinished projects?) The original rear hatch badges for a 72 240z.(i think its "datsun" and "240z" in script BUT i could be wrong.) The drivers side rear trim bit that goes around the fixed side window(interior)--in black. The original drivers seat belt- in good nick. A perfect center console- the one without the choke knob(or even a perfect dash- but i think thats a dream.) or even some recoed door trims.... one of the pull off plastic knobs off the heater slide switches. Front and rear strut braces--new or old style. a good …
Last reply by 240 in OZ, -
- 4 replies
- 839 views
I am looking for a gas tank for my '72 240Z - I'm not particular as to it being the exact match, just so long as it fits and works. Thanks. Matt
Last reply by tyrfryr, -
- 2 replies
- 1.1k views
I'm looking for either the stock orange air cleaner that came on the '72 Z or some aftermarket air cleaners that will work well with the SU's
Last reply by Zracer40, -
- 0 replies
- 517 views
Hi! this is my first time here, and I can't say how great it is to have found this site!! I just bought a '72 240z last sat. Everything seems to be in order except for the fuse box. the fuse holder slot that deals with my dashlights and rear lights keeps slipping loose. The whole box needs to be replaced, actually, and I am having the hardest time locating a new fuse box. The Nissan dealership told me I was up a creek as they didnt manufacture them anymore. I am in so.cal and all the z cars in the strip yards have been parted out as far as fuseboxes go..... Does anyone know of how to go about locating one somewhere else in the state or country? I'm totally stuck and can…
Last reply by swallozgoo, -
- 1 reply
- 860 views
I'm in the market for a quality heater control panel with the switch and controls both intact. Knobs are important too. Thanks.
Last reply by 2ManyZs, -
- 1 reply
- 603 views
I am interestemd in purchasing a minor cracked to non cracked dashpad or dash assembly. I live in the SoCal area. please PM or E-mail.
Last reply by grunt0311, -
- 7 replies
- 942 views
I need a single black vinyl seat bottom to match the one in my car (pictured below)...in similarly great shape. Driver or Passenger. I've heard that a passenger seat can be installed on the drivers side or that I could take a passanger vinyl/ foam and replace my driver's vinyl/ foam. This way my recline lever won't be on the wrong side. I'm in the SF Bay area. Thanks!
Last reply by orange240z, -
- 0 replies
- 645 views
Looking for a set of four in excellent condition. Need with red "Z" centers. Please contact me at djstein@cbre.com or 503-936-5411 Thanks, Dan Stein
Last reply by Dan Stein,
-
Recently Browsing 0 members
- No registered users viewing this page.