Topics Last Week

Update for all of you. We very may be in business here and you were all right - the hydraulic line was crooked/not fully seated and once I took it out and reseated it, the leak was gone. Again, I still don't understand how it didn't leak over the course of 6 years and thousands of miles, but I guess that was a good thing. I am going to bleed the brakes tomorrow just to be safe but I did bleed the master after all of this and the pedal feels good. Here are pictures of the line screwed in before, the flange/nut's condition when I took it out this evening, and how the cylinder looks now with the line in straight.

I am in Bellingham, WA 98229

Another component bites the dust, opened up my fuel pump relay only to find a similar fate as the ignition module. Weird part is, the relay looked like it might have been taken apart once already, but the guts say otherwise. I wonder if all the relays on the passenger side will be like this also. I pulled this link from a post I found here and ordered one. And I also pulled the color wiring diagram from here and had the local printer blow it up. Now I can actually read it.

1977 280z AFM from an EFI engine. Car had been sitting, everything looks in working order. asking $150 obo. located in Gilbert AZ

ok, will check that out, since I have already pulled the alternator, took a whole 20minutes........ I guess I can check to see if there is continuity from the battery terminal to the "T" connector? Is there a fuse inline somewhere? I know there is a fusible link come off the starter..........

Give me a call

I worked on the heat shield/ cable bracket some more today. Here is the current pattern An earlier template on a piece of coil metal I glued it to piece of 16ga I had laying around A little cutting We will have to clearance it around some of the header pipes. Since it's an equal length header, they intrude on the carb area more than some We will use some stainless exhaust tube to deal with the clearanced areas. Once I finalize a design I will have sendcutsend fabricate it for me

I also got the tool covers from resurrected classics and got them installed A little nerve racking to bend the plastic hinges to mount them

Planning to swap an R200 into my Series 1 car (12/70 build date) and am looking for the mustache bar, front diff mount and insulator and the rear transverse link mount from a later 280Z that came with the R200.

Sent PM

Awe man this is a trap!

S30 parts are rare and expensive. Not enough competition or volume of sales to keep the price down.

This is the other name and email used during the email communications with Sully. Phaedra Rosengarth armychick44@hotmail.com He sent several pictures of the new tank and a few pictures of a partially restored tank that he allegedly was working on.

@Mike

For sale are 3 280zx gauge clusters (without clocks). One is for a right hand drive. I make no claim as to the function of the 2 gauges per cluster, but they should be good. Asking $15 plus shipping If interested contact me @ ron@zclocks.com

The reason I mess up when talking about ChatGPT with my colleagues on campus…

This bot is not like the others. The link actually leads to a real business. In Dubai.

Roof in really nice shape….a surprise. Frame rails, outer rockers and floors toast ….not a surprise. Firewall, spare tire well and inner fenders are nice..surprise. Tunnel and inner rocker area in great shape, perfect to attach new floors. Have rails, need both floors. I’ve seen gnose cars trim lips off the rear to allow wider/lower tires/suspension. Debating on leaving them trimmed off, or replace entire rear quarters to have the complete outer rear well.

The first picture from the left shows a completed repaired hi- lo beam switch circuit board repair. The next 2 pictures show continuity on both of the hi- lo beam switch closed circuits. In the mail on the way I have a parts turn signal switch with broken hi- lo beam switch circuit board. In the near future I can detail my repair protocol if there is interest out in Datsunland.

I also used an electric knife on my seat foam and it worked just fine.

Both the original tensioner and the new one have rubber type washers between the tensioner pad and it's housing.

Seek and ye shall find! I was able to find it and jumper the connection. It was really burried at the back. For others coming to this thread, when looking at the two wire bundles from the passenger side it's connected to the one on the right. It splits off from that. (see pic with finger pointing to it) Just grab the smaller taped up bit coming off it and start pulling. The Nismo pump is a bit noisier than I'd like but I'm really happy none the less. Initial pressure on start up is around 6psi and then once it warmed up it dropped to 4 to 4.5psi. I've moved the red wire from the + side of the coil to the ballast and it runs. But, I've currently got a intermittent misfire on two cylinders. Number 2 and 5. I found them by attaching the timing light plug wire connector to them and the light flash wasn't consistent. I've ordered new NGK plug wires, plugs, cap and rotor. I'm not sure of the cap and rotor though. I went ahead and assumed they're for an L28 though I could be wrong. How can I identify the difference between a L24 distributor and one for an L28? I'm guessing they're not identical. I know the 240Z had points and the 280Z didn't. As the car has a L28 from 2000 I'm assuming they also threw in a later distributor with the Pertronix. I pulled the plugs and they were really sooty. I cleaned them with a wire brush and that didn't really help. I'm wondering if it's my ignition or if I'm just running super rich. Both of those are on the most direct line from the carbs and I'm assuming would be getting a more fuel than the other cylinders to their sides. Brakes also need to be fully bled as I've installed the 8.5" booster upgrade from JDM-Car-Parts and new master cylinder as well. So it drives and stops and can be driven around a parking lot or paint shop if need be.

OK. Just got the last of the plugs in. I like the M16 x 1.5 low headed plugs to fill the inside ports of the intake when one has removed the water heating. Purchased them from Belmetric.

Well, Here I am, a year late, but better late than never! I paid $3,000.00 for my all original, 100,000 mile, 12/70, 1971 240Z in 2006.

Between Iran and Saudi Arabia