Blog ricky86

Sign in to follow this  
  • entry
    1
  • comment
    1
  • views
    1,037

I have 1and 1/2half 1980 280zx’s a 2+2 that is in pieces but runs good

Sign in to follow this  
ricky86

418 views

I have 1and 1/2half 1980 280zx’s a 2+2 that is in pieces but runs good and a 80 2 setter w t-tops full car hasn’t turned over yet but haven’t tried2 hard 2 work on it the 2+2 engine purrs both 5 speeds Basically one car 2 engines got turbochargers lying round the shop id like 2 turbo charge one of em and keep one stock!! Can anyone help?

Sign in to follow this  


1 Comment


Recommended Comments

and id like 2 twin turbo one and have one stock but where would i find the manifold the right pistons so forth and so on and would the trans hold up? i just don't know but i want her 2 fly and can u swap 2+2 engines w base engines? ive got turbos but would it be cheaper 2 drop a v8? put in a vett trans? but then its not really a datsun

Share this comment


Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Blog Statistics

    • Total Blogs
      168
    • Total Entries
      250
  • Blog Comments

    • I'm still waiting on a hoist to free up before I can start bolting the new brake parts on my Z, but I did make the drill jig today.  I started with a 12mm thick Mustang wheel spacer with a pilot.  I then made a drawing to layout the holes needed.  I transfered the drawing onto the spacer and I drilled three new 1/8" holes through the jig (spacer) so I'd have the correct 4x114.3mm holes.  One hole is shared from the original 5 lug rotor.  I then bolted the jig onto the Mustang rotor and simply dr
    • Local radiator repair shops used to be plentiful but getting harder to find.  Some of them just specialize in big truck-heavy equipment radiators.  I will be needing to do the same for my project.  I have heard good reports on gas tank RENU but there are none of those franchises in my area.  Good luck, John-Lugoff, SC
    • Decided to go with the 240sx conversion. Main reason is it’s strictly for the street and the parts were easy to source. What I didn’t realize was the 14” wheels won’t clear the caliper. Now looking for a set of 4 lug 15” rims and tires I can use during the build process. Can anyone recommend a temporary solution as far as make and model preferably a steel wheel that I can use until I’m ready to buy the wheel and tire combination at the end of the project? Thanks again for all the help out there.
    • There are several reasons to use the S197 rear brakes.  The rotors are larger diameter than the SVO rotors and they are vented.  The calipers have larger pistons to give them more power.  The big beef with the Maxima rears is that they don't offer as much stopping power as the stock drums.  The S197 rears allow the addition of an adjustable proportioning valve.  The Maxima rears cannot utilize an adjustable prop since the prop needs to be all the way open to get close to enough rear bias. 
    • Any particular reason to use S197 Mustang 5-lug brakes?  The Fox body SVO Mustangs had rear discs with 4-lug.  It's a popular swap to use SVO or T-bird Turbo Coupe rear brakes to retrofit discs to other Fox body Mustangs.  These parts are still pretty common (probably available as a kit).  Might be worth checking to see if they'll fit.