- valve train noise
- can u use a borg warner from a 300zx in 240z
- Performance Cam Pulley
- 4-speed w/ new diff
- I need some direction on my problem.
- Small Intake question
- How to remove differential?
- New Spider gears
- Revving problem is solved!!
- Fuel Injector Question D1560BA
- You can't trust your FSM?
- Can anyone recommend someone to rebuild a 5-speed transmission
- Water Pump to Fan Stud Size?
- Gas/Amp dashboard gauge from a 74
- Half-Shaft Bolts
- smog rail removal?...
- 3.5 to 3.9 diff
- Good point on block rebuild...
- Help with Webers, Distributor, Ignition Coil
- R200 rear diff into early Z
- Spare Diff delivered, question about casting
- Question on modified E31 HEAD
- Oil thread
- Lame labor day (for me).....
- blue smoke how come
- Solid Front Differential Mount?
- Car shudders on deceleration at 110kph+, diff strap too loose?
- HELP! Clutch grinding, very stiff 1st shift!
- crankshaft pulley
- Engine ID help; z or zx?
- Has anyone used or recommend Alumiseal?
- L28 Stroker project
- Creaky Clutch
- Differential Damper
- Iridium Spark Plugs
- Air Intake Canister VS. Stock Box
- L24 performance upgrades.
- my motor blew
- Varying idle rpm and lack of power at take off
- Stubborn Rear Axle Nuts. Nuts!!
- mustache bar bushing removal questions
- Still smokin
- Correct head gasket for 83 280zx
- Not Urgent...Clutch help
- Shift lever and knob spinning together?
- R160 ring gear into '77 R200 ?
- '78 air flow meter question
- clutch and flywheel recommendation
- Desmogging the Z
- New Slave.....No Result
- This could happen to you
- Head questions
- 260Z Zombie parts?
- Dyno Chart
- Turbo 350 Transmission
- What causes rocker arms to pop off?
- need help, erratic engine
- Awakening a long sleeper
- Transmission Mount Issue
- Opinion needed
- Which clutch to buy?
- L28 Engine/Shop Recommendation
- Spring Screw by TPS
- piston and engine rebuild sources
- How to I confirm matching numbers motor?
- whats the going price for rebuilding a L-28
- Transmission Swap Help
- 4-Speed Tranny Drain/Fill Plugs Stuck
- Question about oil leak
- Wow, is this ugly.
- Better Gearing
- Neoprene Valve cover gasket
- What the heck is THIS?
- Got an R180 (4.11)
- Spark Plug question
- Camshaft question
- Did some weight lifting this morning...
- AEON Aluminum Radiator?
- Purist vs practical
- valve covers
- Pulled the engine/tranny combo
- Differential part number?
- s30 engine mount source???
- Tranny fill capacities
- engine oil cooler
- R&R'd the Diff again yesterday & installed new alum radiator.
- Some ECU questions regarding NA to Turbo L28...
- Help to confirm diff ratio
- Picture of ITG
- Refurbished engines
- Clutch replacement costs
- Motor Mount
- first time out
- disassemble tranny/inspect
- Oil Pump Question
- How to visually ID a FS5C71-A transmission?
- 77 & 78 Intake Manifold Compatibility
- Vacuum Dashpot
- Bob Sharp intake question
- Cylinder Head Removal - Part Two
- Looking for engine L24-063102
- Coolant temp sensor question
- Differential
- Evaluating engine rebuilding shops
- What oil do you use?
- 302 swap trans
- E31 Head Gasket
- Correct Series 1 Radiator
- 280 ZX Auto - Manual conversion
- Aluminum radiator options
- Crazy things happening at 5000 rpm
- Help trouble shoot
- anybody use comp cams?
- transmission/ shifting ease
- Motorsports MSA Aluminum Radiator - Anyone using?
- Flat top pistons
- Replacement Parts - Kyosan/Bosch
- Got my 5 speed
- How can I tell if i have a 5 speed???
- Driveshaft Install-Basic Question
- heat related mix problem
- L24 Oil Pump removal
- valve adjustment
- L26 engine rebuild kits?
- My new project car. Please help
- Y70 Head
- u joint?
- Confiming Crank TDC
- Front sump L28 into a zed
- 5 speed install
- Need help finding for the "net" material.....
- Spinning the Cam
- Engine Progress pics
- need info on '76 280z
- Distributor Question
- E12-80 question
- 240z Valve Cover
- State of my Engine Bay.