Engine & Drivetrain
224 topics in this forum
-
- 1 follower
- 2 replies
- 1.1k views
I am trying to find something that shows me how the vacuum should be connected for AC/Heat and the cruise control. Page 212 of the Hayes manual gets me part of the way there but I still can't find anything (even in th FSM) that shows me where the two vacuum lines coming from the cabin (one red, one blue) would go. I looked through the FSM quite a bit and I am beyond confused. This is for a 1983 280zx non-turbo. Any help is appreciated.
Last reply by rogerwilcos, -
-
- 5 followers
- 22 replies
- 2.5k views
My subscription to this site has been some of the best money I have spent. Thanks to everyone for always taking a look at my issues and helping me out (without making me feel like an idiot!). I have noticed that I keep adding coolant to my reservoir, but within a couple of weeks it is gone. I did some googling last night and this seems to be one of the symptoms of a blown head gasket. I looked around a little bit to see if I could see a leak anywhere. All I am seeing are the leaks below. In addition may oil pan gasket and rear differential cover gasket are both leaking, but don't think it is related. Can someone take a look at these pictures and see if they can…
Last reply by Jeff Berk, -
L28 Main Caos 1 2 3 4 5
by Remixaflip- 5 followers
- 49 replies
- 4.7k views
I just purchased an L28 it’s complete except it’s missing 1 of the 7 main caps. Where can I go to purchase a new set? Sent from my iPhone using Tapatalk
Last reply by Racer X, -
- 6 replies
- 1.5k views
About a year ago, I put a newly refreshed and .080 shaved P79 head on a used stock F54 block. I have since rebuilt the block with new rings/bearings, etc. I also installed a .480 lift cam and new rockers/springs valve seals, and DSI swirl polished valves. I'm running it all with FAST EFI from Zcardepot. It all works great. I've been breaking it in by running it at short full throttle bursts and engine braking down hills. Never over 4k RPM and constantly fluctuating RPM/cruise speed. I have put roughly 175 miles on it so far and have no reason to believe it is not breaking in properly. Plugs look good, no smoke, no oil consumption so far, and it's mak…
Last reply by Reptoid Overlords, -
- 5 replies
- 1.4k views
Been going through my engine for the last couple of months. I'm re installing it in the car and can't for the life of me remember if anything came out of this hole. If so, would someone kindly re educate me. It's roughly in the 11 o'clock position when facing the oil filter housing area. Pictures on google show it not used but I could only find clear pictures of peoples engines on stands(not in car). It's a 1982 F54.
Last reply by siteunseen, -
- 2 followers
- 3 replies
- 1.3k views
I have a stock turbo exhaust manifold from a 82 or 83 that I’m am currently cleaning up. I noticed when I first started cleaning it that it seems to have a few patches black on it. I’m not totally positive it was paint, but I would like to paint it to “preserve” it and keep it from rusting. Were the stock 82-83 turbo manifolds painted black from factory? If not, should I paint it cast iron color? Will be using VHT Flameproof Sent from my iPhone using Tapatalk
Last reply by mailnome, -
- 2 followers
- 8 replies
- 1.6k views
Since it is the winter in Missouri I decided to work on a couple of things with my 1983 280zx while the car is in the garage. I replaced all the fuel injectors and the fuel injector wiring. I also removed the valve cover and cleaned it up, and replaced the gasket. Finally, I ordered one of those silicone hose kit and replaced a bunch of the vacuum tubes that were old and crumbling. I put a new fuel filter in while I was messing with the fuel system. I went to test drive it yesterday and it started up just fine and runs well. I backed it out in to the driveway and the brake pedal dropped down to the floor. I think the brakes work, but just barely. I checked the brake…
Last reply by dutchzcarguy, -
- 4 followers
- 19 replies
- 3.5k views
hello everyone and im sorry if this topic has been discussed before. im restoring a 1983 datsun 280zx with a L28 (non turbo) engine and a few months ago i was finished with the engine resauration and tried starting it up and it started up right away and ran perfect! in the last few weeks the engine had been on a few times (to show my friend). but now this morning the engine does not want to start up at all , the engine goes around but wont start. what is working / have i checked? fuel? : tank is a quarter full and also the fuel rail has presure (fuel flies out when i take of the fuel line) spark? : yes a strong spark with new spark plugs when i tr…
Last reply by dutchzcarguy, -
- 2 followers
- 3 replies
- 1.3k views
Hi guys, This time i'm going to refresh The engine of my 280zx as i can predict that the seals and all will fail one time and i want to prevent that (after 42 years !!) So, i'm looking for a good (best) engine or headgasket set. (as i already did the crankseals i think i go for a complete head set of seals/gaskets..) I have found (local in the Netherlands) some brands.. 1. AJUSA (made in spain) makes a set for E89,- 2. Japanparts (Made in Japan? sheap junk??) E23,- (!!) 3. Glaser (no idea) E 50,- 4. ASHIKA (Japanese???) E56,- 5. Payen (Made in UK.) E65,- 6. Blue print (no idea) E143,- So i lean to a set …
Last reply by Captain Obvious, -
- 1 follower
- 0 replies
- 1.2k views
Spotted this problem with the AC clutch in my 1983 280ZX Turbo while changing the sway bar bushings. Looks like a rivet let go. I removed the AC belt so the compressor won't be spinning at all, but looks like I'll need a clutch. I'll be looking for one!
Last reply by Pilgrim, -
- 1 follower
- 8 replies
- 2.6k views
I've seen a few threads regarding aftermarket cams running OE fuel injection. I'd like to briefly revisit the topic. What would the drawbacks be to running a .480 .480 274/274 cam with my stock fuel injection? My engine is an F54 stock internals with .080 shaved P79 with stock cam and valve train. I would replace all necessary valve train components to meet new cam requirements. Thanks for input . I know it's a kind of old topic, but I value current experience here the most.
Last reply by Reptoid Overlords, -
- 2 followers
- 8 replies
- 1.8k views
Hello! I am new here but I have recently started to restore a 1980 280zx and I have had some trouble. First, it took a lot to start but I finally was able to get it running smoothly but shutting it off after 5 minutes just to be safe. Whenever I had gotten in the car I noticed the clutch pedal is completely depressed, no resistance, nothing I pumped it a couple times after pouring brake fluid in the clutch master cylinder but still to no avail there was no pressure. Lastly, (I know this was stupid) I noticed on the engine block, I have no idea what hose or anything but there seems to be a huge opening in that hose, I’ll attach pictures and a video of the clutch pedal if I…
Last reply by Reptoid Overlords,
-
Recently Browsing 0 members
- No registered users viewing this page.