Exhaust
Discussions about the Zcar exhaust system.
389 topics in this forum
-
- 1 follower
- 3 replies
- 178 views
Other than buying one as a part of a full gasket set, can't seem to find anyone carrying this gasket Part #24, 14004-N4300 The exhaust manifold to down pipe gasket for a 76 280 L28. Happy to make my own I guess, but never shopped for gasket material for this high heat application. Anyone have any recommendation on what to use?
Last reply by grannyknot, -
-
- 18 followers
- 491 replies
- 73.7k views
Designed for more road clearance: https://translate.google.com/translate?sl=ja&tl=en&js=y&prev=_t&hl=en&ie=UTF-8&u=http%3A%2F%2Fclicccar.com%2F2017%2F01%2F27%2F440405%2F&edit-text=&act=url
Last reply by ollie, -
- 3 followers
- 51 replies
- 7.6k views
I can't get my pipe to go through the upside down C tunnel below the differential. Anybody run into this or is it just me installing it wrong? Thanks for anything.
Last reply by Jeff G 78, -
- 2 followers
- 20 replies
- 889 views
Since I had to cut off the exhaust to deal with all the rear suspension work, I decided to put together a 3" SS rear section, starting after the existing cat, then going to a 2.5" Stainless Works rear muffler (ran it on my X1/9 K24 swap for a few months). The 3" SS exhaust I put together from a exhaust I had made years ago for my Volvo C30, before I converted it to AWD & had to make it all over again. Forgot to take pic before I cut it up - this is what it was Eyeball the general placement, then cut, & tape together to check clearance off the forward crossmember and lower control pivot & diff casing tack welded, then recheck fit …
Last reply by grannyknot, -
- 1 follower
- 7 replies
- 2.8k views
I have been bitten several times now (you'd think I'd learn...) by oxygen sensors that fail in the first few hours of life. I typically buy the AEM 30-4110 kit from Amazon, good price, shows up quick, blah blah. After a few rapid sensor failures, and me telling AEM, and them quickly sending new sensors under warrantee, and me going and buying "real" (more real??) Bosch sensors, I now have some details to report so you can determine if you get similar "bad" sensors.
Last reply by AK260, -
- 1 follower
- 0 replies
- 275 views
I have been bitten several times now (you'd think I'd learn...) by oxygen sensors that fail in the first few hours of life. I typically buy the AEM 30-4110 kit from Amazon, good price, shows up quick, blah blah. After a few rapid sensor failures, and me telling AEM, and them quickly sending new sensors under warrantee, and me going and buying "real" (more real??) Bosch sensors, I now have some details to report so you can determine if you get similar "bad" sensors.
Last reply by zKars, -
- 3 followers
- 12 replies
- 759 views
I'm having overheating problems if my car sits in a traffic jamb or between heats when I previously did autocross. I've reestablished a fuel return line to replace the deadhead system installed by a PO and did some other minor changes. I don't want to add hood vents. I hesitant to wrap the header and exhaust due to possible overheating the exhaust and trapping moisture but I found a product by Termo Tec. It wraps loosely around the header so it likely will not trap moisture and heat as much as a tight wrap tape. Does anyone have an opinion on this product? https://www.summitracing.com/parts/the-14004#overview
Last reply by Jeff Berk, -
- 2 followers
- 4 replies
- 529 views
Can anyone tell me where I can purchase the Fujitsubo legalis style flanges for the 240Z exhaust system? Datsun garage has them but won’t sell them. Looking for 2
Last reply by heyitsrama, -
- 2 followers
- 7 replies
- 2.4k views
Has anyone installed a SPINTECH Low profile 3000XLF Sportsman muffler on their Z without any resonators? If so, what did it sound like and do you know what the decibels on it were? https://spintechmufflers.com/3000xlf-sportsman-low-profile-muffler/ I looked extensively for some info, but the only thing I found were installations on non-240z vehicles which obviously will have a totally different sound and decibel numbers. Thanks for any info.
Last reply by 240z70, -
- 1 follower
- 1 reply
- 612 views
I’ve been slowly rebuilding/restomodding my 280Z. I only have to have exhaust mounted and some tack welds in the rear sway bar. im looking into twice pipes, but would a traditional set up be better for the Rebello? I’m not well versed on exhausts. Any insight would be appreciated. IMG_7616.MOV
Last reply by siteunseen, -
- 4 followers
- 44 replies
- 2.9k views
now i havent put the center console in yet but each time i drive the car, very short trip, i smell of gas. Everything has been redone professionally. New carbs, headers, exhaust etc... How likely is it its all b/c of the center console? I am thinking got to be more to it that just that.
Last reply by siteunseen, -
- 2 followers
- 4 replies
- 542 views
Pulled out a long stored 240z couple days ago, to look underneath, noticed the paper tag part number still intact in front side of muffler. It is painted black, so it definitely has been replaced at some time. Curious to opinions concerning saving the Paper tag or let it burn off with heat over time . Basically asking if ever in a judged show, would it hurt or help in “stock” class? David
Last reply by kats,
-
Recently Browsing 0 members
- No registered users viewing this page.