Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,083 topics in this forum
-
- 3 replies
- 858 views
Here's a list of items I need to do to my '78 280Z. Help me decide which order to do them in: A/C repair - needs evaporator valve (It is 95 degrees here and this is my daily driver) Clutch - needs new slave cylinder, but just squeeking so far Differential - slow leaking of fluid, needs new seals RPM hold (?) - the device below the throttle body that hangs the rpms between shifts...not working causing tendency to stall and affecting gas mileage Opinions?
Last reply by d240zx2, -
-
- 9 replies
- 897 views
Some of you have been probably following my zcon thread, but I have been doing a complete resto and I am nwo just driving the car around for the first time in years. I am very happy with the way the car handles and performs, but I have one of the 'weird noises' that I am trying to figure out. The noise seems to be coming from the rear and it sounds like a tire with a slight imperfection or slightly out of balance-but there is no shimmy or any vibration. The noise comes in around 55 and goes away around 70mph. Here is the weird part for me; at a constant speed of 60mph where the noise is the greatest in 4th gear, if I shift up to 5th gear the noise almost goes away. Shift …
Last reply by Shade133, -
- 3 replies
- 721 views
ok, got new battery and the plug wires connected... tried to start it and no go.... fuel gauge was empty...so I put some gas in it, but the previous owner said it had half a tank...when I shook the car I could hear what I guess is the sending unit in the tank? is it a floating type sender? anyways...I put more gas in the tank and it started leaking at the rubber hose/hose clamp fitting on the rear of the gas tank......(near the muffler/bumper?) so I figure the tank was really empty prior to me putting gas in it... can I pull the hose clamp/hose and re-cut the hose, re-mount the line and check for leak, add gas? lastly, for the wiring order on the distro cap...it looks …
Last reply by bounce, -
- 1 reply
- 1.1k views
I just have a question about ports in heads. I have a header for sale that is rectangle port,and the gentleman that wants to purchase it from me has round ports on his head. My question is will the header designed for rectangle ports ,work on a round port head?
Last reply by Mike B, -
- 8 replies
- 929 views
I was hoping that cheap stuff will work...but , rust oleum? better stuff? pray tell?...hthaks
Last reply by Powderkeg, -
- 6 replies
- 1.6k views
could someone describe or direct to a site that explains how to clean fuel injectors. my '76 280z had been sitting for some time and i am sure the injectors are leaking and or clogged somewhat. cleaning the inj. may be complicated but before i purchase new ones i would like to give it a shot. thanks
Last reply by Z train, -
- 0 replies
- 560 views
Anybody used EGT sensors for tuning Webers? I have a used set, professionally rebuilt, and am determined to learn how to tune them to perfection. I already have a wide band O2 guage with sensor bungs in EACH header pipe. However, I have only ONE guage. So I have to move the sensor from pipe to pipe to tune it. I'm not willing to pay the $ to get a 6 cylinder guage, but I AM willing to pay for a 6 cylinder exhaust temperature guage. I found a guage from Westach with a switch to change between cylinders, but it is designed for aircraft use and, aparently aircraft engines are specifically designed to use these things. My '72 240, however, is NOT. The sensors are held in pla…
Last reply by 2flabaddog, -
- 5 replies
- 932 views
Hi all, I have a '72 Z and have been cleaning it up on a home garage resto. Body parts are being painted, rear half of the car is having body work finished up. The running gear is in tact, engine, tranny, and rear end. I added headers and exhaust, and removed smog stuff from the intake. It has been awhile since I last had the car running, and when I went to fire the car up, I used a bit of starting fluid to hear it fire. It fires up just fine with the short squirt of starting fluid, but it doesn't seem to be pulling fuel from the tank. I manually sucked fuel up to the filter, so I know there is fuel there. Before I started the resto, the car started up fine and ran l…
Last reply by mlc240z, -
- 4 replies
- 854 views
Hello All, I dug my current project 240 out of a barn in my hometown. No Title or Registration to be found. Is there any way to detemine what year this car is based on either VIN Number, body or frame differences, any clues at all? Any help with this would be greatly appreciated. Thanks!
Last reply by Diseazd, -
- 9 replies
- 1.6k views
Removed electric fuel pump from my 1977 280 Z . I put the pump back on and connected the green wire to larger terminal and black wire to smaller terminal on the pump. I also put a clear filter between the gas tank and the inlet line to the fuel pump. The car is not wanting to start and I'm wondering if I have the two wires connected correctly. I can't see any fuel in the filter I installed and wonder also if the fuel pump has to some way be primed since it is a wet type fuel pump. Any help or suggestions would be appreciated.
Last reply by reddie73, -
- 16 replies
- 6.8k views
Can anyone identify what goes here? I believe this part is the key to getting this vehicle to crank. I've gone through every wiring diagram I can find and cannot account for this plug or what connects to it. Thanks
Last reply by ArnieTX, -
- 5 replies
- 1.9k views
Found this dandy in the trunk of my non-running '77 280Z. Where does this part fit? Does it belong to my car? Lectron part no. 22529628 4341 :stupid: Okay.. so now that I know it doesn't belong.. anybody want it before I donate it to the Goodwill?
Last reply by Panic.attack.77,
-
Recently Browsing 0 members
- No registered users viewing this page.