Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,083 topics in this forum
-
- 8 replies
- 828 views
just back checking myself.... yay or nay? cylinder 6 is closest to the firewall?
Last reply by sblake01, -
-
Oil under pan 1 2
by 260zinsd- 14 replies
- 2k views
HELP!!!!!! Were do you think this oil is coming from?
Last reply by Z train, -
- 15 replies
- 1.8k views
Been battling it for almost 2 hours and actually dented the rear quarter from the inside. It is a small dent from pushing too hard and I am pretty sure my paintless dent guy can get it out. I cannot get it to seat in far enough to install the screws. Unfortunately I lost all my pictures from when I removed it so I have no reference.:stupid: I have an early series 1 california car and want to keep it original. Any help would be very appreciated. Thank in advance. John Happy Fathers Day (where applicable)
Last reply by zKars, -
:bulb:Hey. Im new to the forum (post wise) ive read a lot of stuff on here over the last year, never had to post until now . So hello, Anyways. i have an issue with my 78 280z l28 (cold air intake, 2.25 exhaust glasspack muffler) 5 speed (straight gears). It is an arizona car and i need to pass emissions here so i can get my plates and registration. I can get the car to run great under a load and WOT with no miss or studdering. but my issue is idle. It has a rough idle. clearly a miss and rich exhaust. Ive taken it to emissions twice. The first time i took it was bone stock. no cold air intake, no exhaust. nothing done to it. and it passed everything within spec …
Last reply by Shade133, -
- 0 replies
- 879 views
Hello Everyone, Does anyone have a photo of the EFI Main Relay wiring on a late 78 280z from the EFI main relay socket out as it hooks up to the various wires. We have tried to hook it up as per the FSM wiring diagram and blew terminal 71 this is one of the terminals that are connected to the 40 amp fusible link. The previous owner did some creative wiring and it is now very difficult to figure out what was done. Thanks for any help that you can give me.
Last reply by 78zcar_blue, -
- 3 replies
- 632 views
Yes I've got a lot of questions . I did the upgrade. My ammeter has become annoying. I'm sure I need a voltmeter now. Is there any potential for electrical problems there?
Last reply by Mikez73, -
- 4 replies
- 708 views
I'm going to order points/condenser, distributor cap and rotor....are these four parts what I need to eliminate my spark hunting endeavor? (and then I'll address the fuel aspects of troubleshooting) it seems that way...but more so as far as changing out these parts for new ones....it's good practice to get new ones with a new car purchase?? they do look worn....there was buildup between the points.. I cannot see spark on plug one when removed..but I'm getting good spark from the coil...
Last reply by bounce, -
- 9 replies
- 2k views
240z 71 is that really bad ? or normal? is it an ignition switch contact?
Last reply by SteveJ, -
- 3 replies
- 1.7k views
Hi, This is my first time posting But I'm stuck and need help I'm rebuilding the eng in my 240 and had the head reworked I'm putting in new exhaust studs but cant find the TQ of the studs into the head and the nuts for the manifold. Any help would be great.
Last reply by esmit208, -
- 2 replies
- 1.1k views
The birth date for my 280z is 11/76 but is titled as a 77. I have been waiting anxiously for the EFI relay to arrive, it did- and I have literally torn this car apart looking for the old one. Should I be looking for parts for a 76 instead of a 77? Any help would be appreciated. Gina
Last reply by sblake01, -
- 13 replies
- 1.1k views
Yes I was happy when it finally fired up I still need to set the timing and tape up and loom all the wiring. The car turns off with the key so apparently I got the 280zx alt swap right too. The retired mechanic across the street came over and heard it run. He thinks the dizzy is "off one tooth." I don't really agree with that. I told him the car has an aftermarket "performance" cam and he said "oh that may be what I hear." I dunno. I know the dizzy can't be installed one tooth off or even backwards because of the offset key. Can the oil pump be installed one tooth off? Personally I don't think this is the problem. I think the car hasn't run in awhile, it wasn't warme…
Last reply by TBone028, -
*I want to lower my 260Z..... *Should I cut the springs? *How much should I cut? *Do I need a spring clamp to get them off? *Are the springs the only way to lower the Z *I seen some that are adjustable,but they were for 240Z.How much will they adjust *Any advice would help. *Thanks.
Last reply by az240z,
-
Recently Browsing 0 members
- No registered users viewing this page.
