Engine and Drivetrain
91 topics in this forum
-
- 2 replies
- 2.7k views
Recently purchased 240 with SU dome top carbs. Who is the best person in Austin Texas to fine tune carbs?
Last reply by Bruce Palmer, -
-
- 0 replies
- 1.5k views
Does anyone have any good 240K engine mounts they want to sell or know where to buy them cheap?
Last reply by Disco Bob, -
- 5 replies
- 1.9k views
I'm looking at getting some Headers for the C110 but there doesn't seem to much available anymore. The only type i can find are from Hitech and are press bent not mandrel. They also share the same part number (HTH065) as the C210, R30, 240c and patrol. Do these actually fit and Is there anything else available, preferably mandrel bent? I know that 240z ones don't fit but where to they foul? if it's after the collectors then it wouldn't be too hard to modify them to fit.
Last reply by nikkid, -
- 4 replies
- 2.9k views
Hi ive got a datsun 240k with a single down draft carb on it which is running rich. the blugs in it are as black as and i have alot of soot in my exhaust. also when you rev it up in neutral and the take your foot of and then rev it again it dumps out a big black smoke cloud. also when your driving it and you roll up to an intersection and stop and then put your foot down to take off (its an auto) if you put your foot down probably more then 1/4 to 1/2 throttle she dies like she floods her self. ive been all over the ignition, timing and everything its all good. tho i have no idea where to start with carbs. if any one can give me any pointers to go of from what i have expl…
Last reply by mark105, -
- 11 replies
- 3.2k views
Just wanted to post a note here to confirm that 240Z extractors will not fit a 240K without serious modification. Reason being the steering gets in the way. Recirculating ball as opposed to rack and pinion. I found out the hard way, $270 worse off, let's see if I can sell some Z extractors.
Last reply by Gee, -
- 16 replies
- 4.5k views
As title states im after a new radiator and was thinking of just buying an ebay special if both cars are the same. Cheers Brad
Last reply by Datsun Des, -
- 6 replies
- 2.6k views
Hi Guys, Can anyone confirm if a standard 260Z 5 speed manual gearbox will bolt straight up to an L24 engine from a 240K? I want to change from a Auto to Manual gearbox, and am not sure if one of these will fit. Are all the Datsun L series gearboxes compatable, or are there slight variations that I need to know about? I just want to know which gearboxes I could use if I'm keeping the L24 in my 240K. Any help or advice is appreciated. Cheers.
Last reply by ovenfood, -
- 0 replies
- 1.8k views
I have a 3-gear 'Hollinger' style gearbox which has become surplus to my needs. it was built by Ivan albin in 1997. It's done a few miles, but still works well. it was rebuilt about 4 years ago. its a brass syncro box. If anyone is interested, please let me know/make me an offer. new ones are about $3000, but i'd be happy to take maybe $1300. I'd prefer it went somewhere here than onto fleabay. cheers, Matt.
Last reply by matt240K, -
- 4 replies
- 2.8k views
Does anyone know if the accelerator shaft support bush is still available? All of the ones I have are crumbling to pieces. Is the part number 18311 P1100?
Last reply by 240k Style, -
- 3 replies
- 3.3k views
Hi, another easy DIY, I brought this from Super Cheap ($15), it's a perfect fit, no screws needed, it just sort of 'clips into place' make sure you get a sealed type of radiator cap ($8), so the water sucks back into the radiator when it cools. Nigel
Last reply by Noddle, -
- 7 replies
- 2.8k views
Let's play... What clutch is that! This is the clutch that came out of my parts car. It is a larger overall diameter and thicker than the standard 240K clutch... so my question is, what is it!? At Repco they now have 2 clutches we think could be right. They're so damn similar though... a S14 200SX Silvia clutch and a 280ZX clutch. Surely it's got to the the 280ZX clutch? However, it's a little bit different to this one. The biggest difference is the side - it's missing the bit I have circled in red. The 200SX clutch has this bit though... I just don't know. I would hate to get a clutch to find it not the right one at all and just waste $200 odd. I am leaning towards t…
Last reply by 440k, -
- 6 replies
- 2.9k views
I have just ordered a radiator from Aussie Desert Coolers, the reason I mention this is that Norm (the owner) had just made a radiator for another 240k 2 weeks ago. It surprised me a little as usually when I order stuff I get the "I haven't seen/heard of one of those cars for a while" it was good to know that the aussie 240k scene is still going strong.
Last reply by 240kconvertible,
-
Recently Browsing 0 members
- No registered users viewing this page.