Engine and Drivetrain
91 topics in this forum
-
- 1 follower
- 2 replies
- 3k views
help ran my two door out petrol for 6 months clogged every thing lines carby much tears car is a total virgin never been touched carby never off .slit pins original for japan omg boot masonite never removed spare wheel disc has all four foam tabs on it spare like new idle mixture plastic limiting cap still on i hate touching it as every touch is visable to the trained eye ive got it running sweet but not sure which side the larger air bleed jet goes one large one small in primary and secondary venturis just under carby top visable down throat first time on forum so anything possible comp…
Last reply by Perth 240, -
-
- 1 follower
- 10 replies
- 3.9k views
Hi guys, How are you?? First of all id like to say gday as im new around here and recently purchased a 240K coupe. I just had to say what a great little forum here. Im doing my 240k up into a GTR and i apologise in advance as i know this has been done to death but....its question about my current pedal box in my coupe. So being a auto and doing all the reading from this website and others im going to finally do the conversion. The hardest part is the pedal box im lead to believe..... BUT i got under my dash tonight and found a nice surprise and just wanted to confirm first that in fact im already set up to accept the clutch pedal....... It looks like it …
Last reply by 240k Style, -
- 2 replies
- 2.3k views
Can anyone help me with a few specs. I don't have my manual with me and I need to know the clearance specs for main and conrod bearings. Thanks
Last reply by Yamahacam, -
l26 in 240k 1 2
by Dat 240K- 12 replies
- 5.9k views
when i fisrt joined i read something about puting L28's into the k's and how you have to drill new hole for the dip stick dose this apply with the L26 as well because i have a l26 that i am planing on dropping into my k by the look of the sump on the 26/24 they look a hell of alot differant. Then i was also thinkin that if the dip sticks are located in the same spot could i just swap the sumps and the oil pick ups over? also i have no idea what the l26 is out of as it just had a single down draght carby on it.
Last reply by 240k Style, -
- 4 replies
- 2.8k views
Does anyone know if the accelerator shaft support bush is still available? All of the ones I have are crumbling to pieces. Is the part number 18311 P1100?
Last reply by 240k Style, -
- 31 replies
- 16.1k views
im contemplating on swaping a v8 and a 9inch ford rear end into my 74 kenmeri. has anyone here done this?? if so i would love to see pics..
Last reply by 240k Style, -
- 1 reply
- 3.5k views
Hi Guys, I think i have been done over once more by replacement suspension bushes i have been trying to get my car ready to come off the rotisserie to get it to a shop, its the first time the suspension has gone on since sand blasting.. I had bought a set of replacement nolathane rear crossmember bushes (part number 49060), which in them selves cost a bomb.. and had the factory bushes pressed out of the crossmember by a mechanic, of course i trusted that the new ones would be ok.. The bushes fit, however the rubber extend probably about 1cm above and below the crossmember, in comparison, the factory bushes (from what i have documented) are actually sucken below the …
Last reply by khughes, -
- 2 replies
- 3.2k views
The exhaust on my 110 has just about given up and I am looking to replace it. Exhaust shop thought I would be best to go for 2 inch pipe and fit my twin outlet headers. I currently have headers that have a single outlet but my parts car has the twin outlet version, must be manual/auto thing. I am sticking with the single carb for now so what are your thoughts on pipe diameter and manifolds to get good performance and nice note without the dreaded drone.
Last reply by Yamahacam, -
- 16 replies
- 4.5k views
As title states im after a new radiator and was thinking of just buying an ebay special if both cars are the same. Cheers Brad
Last reply by Datsun Des, -
- 7 replies
- 5.1k views
As the title says im after a EFi setup on my yonmeri i hate carbies with a passion an want it swapped out asap. so question is can i bolt on the efi setup an run an external fuel pump an drive off? will i need to go down a size in injectors? anyways cheers!
Last reply by EuroDat, -
- 0 replies
- 2.4k views
well- I've done what i could in finding out why the car won't idle without the choke. I've pulled each of the Mikuni carbs out from the L28 and cleaned all the jets, but it still won't idle for some reason. I have fuel pressure, but i suspect it may be a fuel related issue as the car had been sitting for around a year. I did treat the fuel and added some new fuel along with some octane boost. So i figure it's time to take it in to a shop who know's what they are doing . I was hoping someone on here could point me in the right direction...a shop somewhere around LA county preferably.
Last reply by Tyrone, -
- 6 replies
- 5.8k views
Pretty sure I had a problem trying to get one of these years ago. I am missing the thremostat housing/water outlet or inlet. Bolts on side of head in front inlet manifold. Can I get one new or is it wreckers only?
Last reply by Yamahacam,
-
Recently Browsing 0 members
- No registered users viewing this page.