Interior
Discussions about the interior components of your early Zcar.
2,351 topics in this forum
-
- 2 followers
- 12 replies
- 190 views
My speedometer needle always seemed a bit weak in that it moved down/up when you drive over bumps or rough pavement. Is that just how these speedometers are? I have a dash cap on meaning the speedometer can't/won't come out. This is just a general question.
Last reply by Patcon, -
-
- 2 followers
- 3 replies
- 245 views
Many years ago, the knob that goes on the seat slider handle in my 260Z broke. I had seen parts on FB from a place called The Unobtanium, and I found they sold their parts on ebay. I decided to get a replacement knob from them. https://www.ebay.com/itm/386245878688 Compared to the aluminum knobs sold by MSA, I figured it was worth the money to get the plastic knob. The new knob is a dull finish compared to the ones installed in the 73 (and in the 74). I think some of the 3D printing artifacts are visible, too. I had to heat it up slightly to slide on. While it may not look original, it's much better than no knob. To me it was worth the money. If…
Last reply by inline6, -
- 5 followers
- 12 replies
- 840 views
I found this carpet and matching jute on eBay. It looked original to me, and I was interested in getting it for the purpose of using it as a pattern for having some custom carpet made because my opinion is that the kits that are available these days are rather lackluster. When I spread it out and took a close look at it, I was surprised. I was expecting it to be loop carpet. However, it seems like it is more of a pile carpet type. To my understanding, one of the most "authentic" carpet kits currently available is this. But, that is loop carpet - it is very different. While from pictures, it may be hard to tell, this carpet definitely isn't co…
Last reply by Zpenman, -
- 5 followers
- 20 replies
- 774 views
240z sign of my glove box came off should i use crazy glue or epoxy to paste it back?
Last reply by jalexquijano, -
- 2 followers
- 6 replies
- 370 views
Hey, I've got a 73 240z and after doing some spelunking it turns out the previous owner had the rear MSA speakerbox setup in the car, and at some point they removed it, and just left the speaker wire in the back. I want to install a pair of speakers in the back, and like the cleaner look of mounting them behind the interior panels with matching mounts on each side, similar to how the original speaker was mounted, but was curious if anyone had any experience on what the sound quality of the speaker behind the panel was like? I can't imagine it's particularly great, but wanted to check. If that doesn't work, I'll probably move forward with fabricating my own speak…
Last reply by AK260, -
- 1 follower
- 3 replies
- 423 views
So I am going to start a leather interior trim thread. I bought the pieces from Interior Innovations and thought it might be helpful to document how I went about the install So I've been procrastinating on this a little bit. The factory vinyl laps up onto the luggage panel a little bit, I believe. I thought that would be hard to do with the leather thickness. Also it really needed to be shifted as far forward as possible to line up well with the parking brake and get under the fire wall mat. There was one set of marks for the seat rib. I will cut these nice and close later I put the original console in the car. It won't be the…
Last reply by Patcon, -
- 2 followers
- 4 replies
- 234 views
Has anyone tried doing a fiberglass repair on this portion of the center console? mine is in decent shape except the rear inner section of the arm rest. Any ideas? previous threads or videos would be great.
Last reply by Patcon, -
- 13 followers
- 192 replies
- 162.7k views
The dashboard in my car had some serious cracks along the top but I couldn't pull the trigger to send it off for rework because of the cost. I wanted to try to repair it somehow though, I had to try something! Here's a few pictures of the cracks. Because of the limit on pictures in each post, I'll upload the balance of the pictures and the materials used after this. Bruce
Last reply by moritz55, -
- 4 followers
- 17 replies
- 1k views
Has anyone had dealings with Interior Innovations? I wanted to see how your experience was
Last reply by Patcon, -
- 1 follower
- 12 replies
- 528 views
Trying to figure out if anyone has done this. I want to move the new seat belts to the towers if possible. I don't see how or if I can access the underside of the outer strut tower area where the seat belt reels attach on the 77-78 MY. It looks like that is a closed off area. Pic courtesy of CO My wheel arch - don't recall there being a way to reach into the outer section from below
Last reply by HusseinHolland, -
- 9 followers
- 97 replies
- 19.6k views
Got a message the other day of someone selling some black leather 350z seats and I couldn't say no. Well I could of, but the price was great. Being they had red stitching kind of sealed the deal- lol. they are power heated seats so I will have wiring to do plus some fab work. Looking forward to having some more flexibility and comfort in my ride. I guess there will be some 1st gen seats on the market soon! well I would have posted a pic but the upload keeps failing
Last reply by HusseinHolland, -
- 1 follower
- 4 replies
- 240 views
Hey guys, I am rewebbing my seatbelt and ran into a problem For the life of me I can't get the new webbing through the small slot that is available. Is this thing supposed to disassemble further before I put the webbing in, or does anyone have experience on how to do this? I have tried tying twine to the belt and feeding it through the mechanism. Then I would tug on the twine to pull the belt through, but I still can't seem to do it. It is just too tight to get the belt to feed in that tight of a circle. I found this @Captain Obvious , but unfortunately, pictures are no longer available. I have pulled off the plastic pieces, but my latch mechanism works …
Last reply by Captain Obvious,
-
Recently Browsing 0 members
- No registered users viewing this page.