Suspension & Steering
Post your questions and answers about these major components of the Zcar and anything related.
2,200 topics in this forum
-
- 11 replies
- 1.6k views
Hi all - Got to work today on the 71. I am planning on pulling the rear end out of the car as well as a rebuild of the rear suspension and noticed several paint marks on the bolts. I was wondering if anyone knows if they are factory marks, or are they from some other odd source?
Last reply by lbpdz, -
-
- 6 replies
- 1.4k views
Does anyone know if the s30 steering rack is available anywhere,and at what cost?
Last reply by Inf, -
- 1 reply
- 1.3k views
hello! being this is my first post on here i want to say ahead of time for the help from everyone! as my name shows i am a mopar or chrysler guy but i have a niche in my heart for datsuns! well i am getting a 72 240 stick for free! finaly! so i want to make it my daily but want to upgrade suspention and what not. so if u were looking to make a nice streetable, fun, fast, on rails handling car what would u do? im looking for brands of parts to go with and stuff that isnt any good! it does need a clutch so i was going to get the centerforce I kit. so for all the help i thank u ahead of time! Thx Ed
Last reply by spitz17, -
- 6 replies
- 1.4k views
I've got a new set of Eibachs, and they are pretty light on the destructions. Two of them are shorter and have tighter coils that change to wider near the ends, and the other two are longer and are more linear in design. Also, which way up should I install these? Tighter coils on the bottom and wider towards the top, or tighter coils up top and wider on the bottom? I should be able to get a picture up at lunch.
Last reply by jmortensen, -
- 2 replies
- 1.2k views
hi guys, im planning to rebuild the suspension but i dont know what do i need to feel it like new? i just have the tokico struts/springs and the energy master kit what else do i need for the suspension & steering ? thanks.
Last reply by Zs-ondabrain, -
- 3 replies
- 1.3k views
I am replacing my strut inserts rear and front, (Rear) we disconnected the parking brake, brake line, removed the 4 bolts holding the shaft to the hub and strut bar link. removed the 3 tower nuts and lowered the assembly and swung it out. Compressed the spring and removed the insert nut. removed the insulator and spring carage. The insulator has a bushing pressed into it, but i saw no bump stop ???? where does it go ???
Last reply by kjphilippona, -
- 3 replies
- 1.6k views
I am rebuilding the front suspension on my 72 240z and I have two metal plates that are about 2.5 in by 6in with two holes in them. I thought they were stiffener plates for the motor mounts but I don't see how they fit. These are not shown in any of my service manuals. Any ideas where they go? Thanks Bob M
Last reply by Koplitzzz, -
- 15 replies
- 5.5k views
Well I'm finally getting to pull the front brakes apart on my recently acquired 71 240z. The rotors need to be replaced (or turned at least) as they are pretty rusty. The calipers need to be checked yet. I will probably replace the pads just because they have been sitting for 25 years untouched - they have plenty of thickness. Any comments on that part of the process are welcome as well but my primary concern here is the tie rods/ends and the ball joints. In the attached pictures the front suspension is just hanging as the car is supported from the center jack point. Are the tie rod ends trashed or do just look like this? To me they look like they should be pulled up t…
Last reply by woytovich, -
- 0 replies
- 1.3k views
Hey guys-- Just bought a 1982 280zx and working diligently to restore it! I have a little issue that maybe somebody here has dealt with before. I'm trying to replace the Power Steering Rack but one of the power steering fluid lines (metal with bolt-like head) has a bolt that is worn down to the point where a wrench cannot grab it successfully! Any thoughts on how to remove it? Or should I scrap it for another line? Thanks!!
Last reply by hoofhearted, -
- 2 replies
- 1.5k views
I own a 77 280z. I've installed Tokico springs and shocks, but would still like the car to drop a little more. i know that early model 240z's have a shorter/smaller strut mount insulator. will those fit in the rear of my 280z and in an essence lower the rear a bit? thanks for any info.
Last reply by studioti, -
- 8 replies
- 1.7k views
I installed a 1" MSA front sway bar on my '73 with an L28. There is only about 1/8" of clearance between the bar and the oil pump. Does anyone else out there have this experience? If so, to the two ever contact eachother? Thanks.
Last reply by gnosez, -
- 8 replies
- 5.5k views
So I think I figured out why the car dog-tracks a bit. I got a good look at the suspension while the car was getting new tires put on today. Maybe this is the way it's supposed to be and I need to look elsewhere, but it definitely looks like someone at some point needed to replace the left rear LCA and ended up using an inverted right-side one instead. If those two arms have camber and toe designed into their angles, that would definitely explain why the left side is funky. image one, the right side with control arm apparently right-side-up http://s132.photobucket.com/albums/q27/AwwsChwA/z%20parts/?action=view¤t=rightLCA.jpg image two, the left side with what…
Last reply by BTF/PTM,
-
Recently Browsing 0 members
- No registered users viewing this page.